Jump to content
SAU Community

Recommended Posts

1998 Nissan Skyline GTT
around 135,000km
KR4 Silver
Manual Turbo

Recently had a HD Nismo single plate clutch installed. (Firm but not too heavy feel)
Has Stainless Steel Jasma Cat back exhaust, and stainless front pipe.
300x600x76 Front mount intercooler
Nismo clear front indicators.
18" Wheels & good tyres with heaps of tread
OR a set of stocko GTT rims with heaps on them

Vented Carbon fibre Bonnet
Engine is stock and unmodded with excellent compression across the board.
Timing belt, waterpump etc replaced 5000km ago with gates racing belt.
Serviced every 5000km with Castrol Edge synthetic oil.

Bad Points:
Has a Light scratch down passenger side which as you can see by the last 2 pics is visible in some light, and not in others.

NSW Rego to 5th December

Located Just over NSW Border from Vic, Willing to travel basically from melbourne in VIC and as far as Wagga in NSW to meet a buyer (and everywhere inbetween). Good reliable car. Willing to negotiate a little for a quick sale. Preferred Contact is Via Private Message.

post-12420-0-96239900-1361227516_thumb.jpg

post-12420-0-60101900-1361227523_thumb.jpg

post-12420-0-42833400-1361227528_thumb.jpg

post-12420-0-33872000-1361227532_thumb.jpg

You would probally would have sold it by now if it wasnt for the bonnet and wheels, try sought that out and get a good price out of it.

otherwise it looks legit.

Edited by starwarz
  • 1 month later...
  • 4 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...