Jump to content
SAU Community

Recommended Posts

Sierra stage 1 turbo

Scotty dump

Scotty 3" front pipe

Nismo exhaust

Plenum spacer

Scotty actuator mod

Hdi front mount

Transgo shift kit

Turbosmart boost t

I do have a nismo ecu but it isn't fitted as it was running to rich. It will be waiting till I have money to do my emanage

Think thats it haha

sh###t you be running 13eents easy, while i hope for a 14 flat

my mods

dump pipe

custom 3" exaust

shift kit

custom intake pipe

14.1 with these mods 1.9 60 foot

I'm really hoping so. I need a new BOV so hoping that doesn't effect me to much, its bleeding off a bit up high. Also really need an intake pipe to get the most out of my setup. But we will see how we go.

Well not exactly what I had hoped for, 14.02 @161km/h I hit boost cut twice on tgis run. So it should have been a 13 easy. I had boost wound down as low as possible so not sure what to do next. Every other run hit cut a bunch more times so was much slower.

  • 2 weeks later...

Took the car to Hiddenvalley last night, managed a 13.6 at 102 so still doing the same mph, couldn't get my 60 foot under a 2 seconds, very very slippery! They just had scrapped the rubber of and re layed vht hopefully when they get more rubber down it will be better! Plus side I've managed to get my reaction down to .006 so managed to do a number of .406 reactions

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...