Jump to content
SAU Community

R32 Gts-T Absolutely No Accessory Power

Traah221

By Traah221,
in General Maintenance

 Share

Recommended Posts

Traah221 Contributor

Traah221

Posted
Posted

Title says it all, guys. Recently swapped in a Series I Rb25DET, it runs well enough, but I'll be damned if I can't get any of my accessory power to work.

Inoperative items include:

- Gauge Cluster

- Rear lights (Brake, Running, etc)

- Turn Signals (Front and Rear)

- Interior Lights

- Accessories (A/C, heat, power windows, etc)

Items still functioning:

- Headlights

- Radio and Speakers

I'm kind of burnt out and at a complete loss. It's not exactly legal to drive around as it were, so getting these things back would be most appreciated. I figure there is a sole cause for pretty much all of these, hopefully someone else has encountered this random issue.

  • Like 1
  • 2 weeks later...
040122 Collaborator

040122

Posted
Posted

Oi man had identical problem with my 32 and i mean IDENTICAL. Ur windows probably don't work either ?i also kept blowing the accessories fuse. In my case i slammed it in reverse too had and the speed sensor plug fell out of the gear box. All that had to be done was plug it back in. Just look on the drivers side of the gear box and see if there's a loose plug or something like that.

Traah221 Contributor

Traah221

Posted
  • Author
Posted

040122, Crawled around the gearbox for awhile, but no joy on anything unplugged or loose. Since I was using the cruddy screw-jack from a friends car, I couldn't get very far under it to look up higher. It's sad I have to ask, but I want to eliminate every possibility, where exactly on the gearbox is the plug located, just so I can be doubly certain?

Also, thanks a million for the input!

040122 Collaborator

040122

Posted
Posted

Well if its an rb20 gearbox then it should be on the drivers side of the box, bout half way between the top and bottom.....i think, it was easier for me as i have a pit, just got in there with a torch. Are u blowing the accessories fuse? Check that n maybe Google speed sensor for rb. My power steering also screwed up with all those other symtons . Ps replacing the blown fuse won't fix it until after the sensor is fixed.

  • 2 weeks later...
Traah221 Contributor

Traah221

Posted
  • Author
Posted

Alright, I lifted her up and poked around the gearbox, no plugs hanging, all accounted for. So, I started checking everything for continuity back with a Multimeter, and I found my problem. I'm sort of embarrassed to admit this, really, but it was a very stupid oversight. I had compared my bay fusebox with every other R32 on base here, GTS-t, GTS-4, GTRs, all of them run with no 75A Main Fuse. Apparently, for reasons I don't want to look into, I do need that 75A Main, because I bridged it with a bit of speaker wire and, lo and behold, all my accessories work fine. Thanks for all the input, though, I really appreciate the friendly help!

  • 6 years later...
  • 5 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...