Jump to content
SAU Community

Recommended Posts

Yes.

Apparently ended up in internal disciplinary action for the driver, as it was not his first time.

He cut me off, drastically, so that I had to take evasive action. After I beeped, he then flipped me off and continued to do so up until I pulled over and attempted to gain entry to the bus. He mellowed out after that

Didn't get touched.

Did you get hit?

My old housemate got rear ended, with the driver just driving off.

Ended up going through his insurance, but driver disputed it, claiming my housemate pulled into his lane, reducing his stopping distance

I didn't get hit. Stopped pretty close though. Thank gawd for ebc pads! The backs feel like they have flat spots and I'm also getting a lot of vibration from both rear wheels. Might give the insurer the heads up.

Edit: could be in for rotors and rubber if this resulted in some damage. Am also picking up some noise from the wheel bearings. It's too wet to go and check right now but will ASAP.

similar thing happen to me... had to brake hard a swerve.

beeped, got the finger.

took photo on the plates and note of location.

reported it via email.

got a call the next day. complained more and informed them I'll go to the media.

Bitch got fired.

suck shit kunt!

Edited by TTT

lol... You braked hard to avoid an impact (as brakes are designed for) and now something is wrong and you think they should fix it?

lol... You got no chance mate.

sounds like your car was not road worthy if shit is broken from braking hard.

lol. It was 60 down to 0 very quickly,. All I'm saying is something isn't right. They've fixed wheels and tyres before when it;s been their fault. Shall hear back next week and go from there.

If you hit a pothole and damaged a rim, I could understand that council may be liable (stretch but still maybe).

If you are driving along doing 60 and a grandma in a hybrid camry pulls out of her parking spot without looking and you jump on the brakes and do a little ABS skiddie and don't have an accident, but later you feel that the rear brakes are a bit weird, is it her fault?

I can't see how someone you "almost" had an accident with could be liable for something on your car failing when used as intended.

Just means that the now faulty part was not road worthy.

If you give first gear a push and hit the limiter, then the next day you find an oil leak, are you calling up Nissan?

i had a bus pull out of a bus stop and nearly take me out one day. i know you are supposed to give way to them etc, but he didn't put the indicator on until i had just passed the back corner of the bus and then just pulled out straight away.

talking to a mate who used to be a bus driver, or work in the management side of things (can't remember which), he said that drivers are supposed to wait something like 4 seconds after they put the indicator on before they even attempt to pull out. on the other hand though, he also said that with the new LED indicators on a lot of buses these days, they can take up to a few seconds to start to flash after the driver puts the indicator on. so that just screws everything up.

I'm glad to hear no one got hurt.

Happens on the Goldie as well. Every time I see a bus at a bus stop I try immediately to merge into the other (right) lane if there is one as IMO they don't give a sh!t about you.

Yes, I understand they have a schedule to run and considering roadworks, school zones, etc... they are always under pressure to meet that schedule hence, why they are pressed for to make up time but at what costs?

HOWEVER.....just because we need to give way to them doesn't mean that they have to be arrogant and abuse it and more importantly tag innocent motorists because of that.

I'm certain its been brought up many times before with translink, Qld transport and other authorities, but bottom line is that justice does not prevail. In addition to that the public transport is already bad as it is

What they fail to realise is that if there is a severe prang resulting from such a situation NO ONE is better off as the bus will be reported in an accident, the passengers may be injured, the bus gets nowhere, passengers get nowhere, the car will be totaled and the driver will be mangled, and bus driver will be let off with slap on the wrist.

Its really about time theses bus drivers start thinking a bit more about safety of the passengers and other motorist instead of just a f@#king timetable which already late anyways.

There I feel better and I hope you do too.

Edited by Ants

To the people that said t they got the driver fired or disciplinary action taken against them. Do you actually have any proof of this happening other than a letter saying action has been taken?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
×
×
  • Create New...