Jump to content
SAU Community

Recommended Posts

.... 13.7 for a relatively stock ls1 in a reasonably heavy car is pretty good going. Your 33 is about the same weight as a commo with no interior or fat chicks. Most people have no idea how fast a flat 13 sec 1/4 really is.

N20 time... :yes:

I do. And this car should be getting close to them IF Nick setups the rear suspension AND tyres.

I'm in a heavier car, running 13.004 down the quarter at 106MPH.

Nick ran originally 13.9@106MPH in a car that is way lighter than I am.

Probably a smaller torque converter would help get this thing off the line easily, OR really really sticky rubber. Chasing more power is not going to help if you are already struggling to put power down at the half way mark...

I do. And this car should be getting close to them IF Nick setups the rear suspension AND tyres.

I'm in a heavier car, running 13.004 down the quarter at 106MPH.

Nick ran originally 13.9@106MPH in a car that is way lighter than I am.

Probably a smaller torque converter would help get this thing off the line easily, OR really really sticky rubber. Chasing more power is not going to help if you are already struggling to put power down at the half way mark...

I have et slicks sitting there, I never dropped my tire pressures the other day and I'm on stiff coil overs :)

I want a 12 second street car... It's just a matter of time

I do. And this car should be getting close to them IF Nick setups the rear suspension AND tyres.

I'm in a heavier car, running 13.004 down the quarter at 106MPH.

Nick ran originally 13.9@106MPH in a car that is way lighter than I am.

Probably a smaller torque converter would help get this thing off the line easily, OR really really sticky rubber. Chasing more power is not going to help if you are already struggling to put power down at the half way mark...

This is true... but for 2nd run at the drags with a poor set up it's not too bad.

As for improvements... Better tires, 0 static rear camber, softer rear springs/shocks, re-angle the rear cradle, adjust ride height to straighten drive shafts, lighten the car more, VHT tire prep.... list goes on. How far do you compromise???

This is true... but for 2nd run at the drags with a poor set up it's not too bad.

As for improvements... Better tires, 0 static rear camber, softer rear springs/shocks, re-angle the rear cradle, adjust ride height to straighten drive shafts, lighten the car more, VHT tire prep.... list goes on. How far do you compromise???

No need to lighten it, it just needs a sensible suspension setup put in it.

Softer rear shocks and springs, get rid of the epic camber, and run low 13s.

PS: My 13.004 was on my first EVER run at the drags... ;)

But Pineapples, different shocks/springs, realign suspension, DONE. Go run flat 13s on same power.

  • 1 month later...

Not really an update but a bit of car activity:

Dropped the oil and changed the oil filter and air filter yesterday preparing the car the the little run it got a Queensland raceway with the supra club yesterday. Overall the day was good with some mighty fast supras there, an even a 1uz powered jza80 (which I actually chopped down the main straight ;) )

So yeah just a few shots from the day.

mvZzTKg.jpg

0efesgi.jpg

dY0YF7C.jpg

Big thanks to QLDSC in particular tara and scott i know how much effort goes into organising events like this aswell as SAU Qld, Mike, Tony, Scot, Boz etc fantastic to see the club moving forward and getting back into some driving orientated events :)

Cheers

Not really an update but a bit of car activity:

Dropped the oil and changed the oil filter and air filter yesterday preparing the car the the little run it got a Queensland raceway with the supra club yesterday. Overall the day was good with some mighty fast supras there, an even a 1uz powered jza80 (which I actually chopped down the main straight ;) )

So yeah just a few shots from the day.

mvZzTKg.jpg

0efesgi.jpg

dY0YF7C.jpg

Big thanks to QLDSC in particular tara and scott i know how much effort goes into organising events like this aswell as SAU Qld, Mike, Tony, Scot, Boz etc fantastic to see the club moving forward and getting back into some driving orientated events :)

Cheers

vids of you chopping v8 supra

vids of you chopping v8 supra

Waiting for boz to finish editing the video, it was closeish actually but this definetly had more grunt must say the thing sounded sexy as sin was basically straight piped

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • planning a r34 rb25 de+t with some other work, rather just have it done in a shop due to space limitations any recommendations? I have most the parts already I seen online Moore Performance and DR Drift any advice appreciated thanks 
    • I’ve read the previous posts so just looking for latest information on how people have dealt with front facing plenum is it a defect etc or didn’t pass roadworthy or was it not noticed? Have a r34 and deciding if I should make a hole on the driver side or not.  I know some people have said blitz return flow but I might get rid of the stock intake down the line for a plenum so I rather set up for that now plus I already have a standard Intercooler. Car is mainly stock  Thanks. 
    • Actually, if having and keeping the stock ECU is the plan, the correct answer is to put Nistune into the ECU and improve the situation, not just look at it.
    • Wrong side of sydney for me coming from Goulburn, but you should head along, all ages of Skylines will be very welcome
    • Yeah so physically that port is consult not OBD2, but also be aware that "JODB" is not really a thing - it came in around 2000(ish) but is not a standard like ODB is, each manufacturer had differences. If you are looking at ECU only and have a standard ECU, go with Datascan as Turbo Tapin said. Per another recent discussion here thought that won't do other systems like in a modern car, for example bleeding ABS
×
×
  • Create New...