Jump to content
SAU Community

Recommended Posts

Any reccomendations as to where to get a tailshaft done in Sydney?

The carbon shaft in my Z32 has failed (again). It seems that heat soak gets to it causing the bond between the yoke and the shaft to slip.

Anyway, planning to get a chrome molly one made up.

Are Sydney Driveline (http://www.sydneydriveline.com/) the guys to see? Any other suggestions? I just want to know that it will be straight and balanced and that they shop is using quality U joints...

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/422368-custom-tailshaft-in-sydney/
Share on other sites

I used these guys for the race car: http://metropolitandriveshafts.com.au/

Excellent driveshaft, no issues with years of use, expensive.

Who supplied the carbon one that failed? Pretty poor to have the bonding fail (twice)

You'll find most driveshaft places (metro) included use CDS tube for their shafts. Nothing wrong with it at all just it's mild steel and far cheaper to the general consumer.

I normally buy 4130 tube from race tech steel, joints from hardy spicer and assemble the shaft myself. Then drop it off at Harry's to be balanced. It's the only way to know exactly what material went into the shaft.

I used these guys for the race car: http://metropolitandriveshafts.com.au/

Excellent driveshaft, no issues with years of use, expensive.

Who supplied the carbon one that failed? Pretty poor to have the bonding fail (twice)

Thanks mate will check it out.

Carbon shaft was from Precision Shaft Technologies in the USA. Owner Mark has been very good about the whole thing, they fixed it the first time under warranty and have offered to do it again. Really though I think it is just a poor choice of tailshaft for a Z32. Heat is the enemy of the carbon shaft and let's face it Zeds make plenty... Especially pushing big HP through big dump pipes/exhaust/etc. Both times the failure has been under near identical circumstances ie driving all day in high ambient temps.

  • 2 weeks later...
  • 1 month later...

Just a quick update for anyone interested. I ended up getting Metropolitan Driveshaft Services http://metropolitandriveshafts.com.au/ to make the shaft.

Went with a 3.5" chrome moly tube with 1350 Hardie Spicer "lubed for life" (I was happy to grease them but these unis have thicker bars) unis.

Came to a total of $1331 which was a fair bit more than I was expecting (had been told by the 2IC that it would be about $800 and they'd call with a quote when the manager was back in the shop, spoke to the manager the following week about what specs I was after and he said they'd source the materials and call back with a quote, next thing it was finished...) BUT all told it does look like being a top quality shaft.

In terms of quality and turnaround I'd be happy to recommend them but would suggest "firmly" requesting a quote prior to assembly to avoid any surprises...

Edited by Rob260

For general info for those doing R33 gearbox upgrades, I had Metropolitan Driveshafts do the tail shaft conversion for my HR31 - cut off the yokes from the 31 and 33 tailshafts and weld the 33 yoke onto the 31 shaft. Good job and only cost $165. They know their business.

  • 10 months later...

Depends how you spec it up man. When you've broken two 'shafts you tend to go overkill, and that's what cost me big bucks.

Metro did an awesome job http://metropolitandriveshafts.com.au/ -not the cheapest but they were recommended by someone in the industry whom I think very highly of.

This is another shop that I looked at http://www.sydneydriveline.com/index.html -they were a little cheaper (going by over the phone quote) but I didn't know anyone with first hand experience...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...