Jump to content
SAU Community

Recommended Posts

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

Not sure your weight figure is correct.

An ARX is 1780kg and an RX is 1680kg.

But if you want to lighten it have a look at changing Electric front seats or removing some of the electronics.

There are not many other places to loose weight as the subframe and suspension are all alloy, bonnet is alloy, boot is plastic composite.

On the upside, all that weight is near perfectly balanced on the chasis with 52% on the front axle and 48% on the rear.

Enjoy.

Nope, RX is awd, as is the RS.

Mine weighed in at 1670kg on the weighbridge at my work.

Considering a stock VE sedan is 1700kg, and even a fully loaded FPV ute is over 1800kg; I don't think there's much to worry about.

I know what I'd rather be driving in an accident.

Or any other time for that matter...

RS if you have triple gauges in the centre, RX if you don't. I think that is a safe measure, unless installed later, right guys?

Or plug in your VIN into something like epc data for the run down.

180sx: 1150kg and three times as powerful as your car.

You Jelly?

^ Yes, yes I am.

I put mine (RS) on the local weighbridge & it came in at 1800kg with me in it, after I had removed all the ususal suspects (spare wheel, tools, sub, mats etc.). All the lux adds weight, no doubt.

I'm not concerned though. This article on the weight of the R35 GTR gives me some peace. http://www.topgear.com/uk/photos/kazutoshi-mizuno-nissan-gtr-interview-top-gear-2012-02-23?imageNo=1

With the right tyres, our cars handle better in torrential rain than most do in the dry.

Your in a wagon who cares for weight loss. Rip out your high flow vq and send it to me. That should save you a good 300 kg, take off your wheels and stick it up on blocks that will save you 100kg give or take. Take out your r35 gtr seats, bc's and swaybars and that should save another 50kg .So that will make you about 250 kg heavier than the 180 but you wont be moving far....

I care for weight loss funny man. That's why I started the thread.

But all you're going to end up with is a noisier, harsher, less pleasant car to drive.

And it might accelerate a poofteenth quicker, or save a bees dick of fuel?

If weight saving was your primary concern; why on earth did you buy a Stagea?

If you do anything to your car that displeases me; I may have to kill you.

Lol, jokes. :whistling:

But seriously; don't. ;)

Edited by Daleo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...