Jump to content
SAU Community

Bayside Blue 99 R34 Gtr V-Spec Engine Bay Question

GZILAH

By GZILAH,
in General Automotive Discussion

 Share

Recommended Posts

GZILAH Explorer

GZILAH

Posted
Posted

Hi all,

Im aware that the 99/00 Bayside Blue GTR's have a black engine bay.

However looking at these pics below of the radiator support bar, on the far left and far right there seems to be a tinge of blue?

For all 99/00 Bayside Blue GTR's owners can you confirm that this is normal or not?

Appreciate all your help & advise, Thank you.

85220732.jpg

44763097.jpg

89869425.jpg

35922877.jpg

44864776.jpg

13942559.jpg

31726258.jpg

Sinista32 Grand Master

Sinista32

Posted
Posted

What does the build plate say.

I don't own one but to me it does not appear right.

I do not believe Nissan would over spray like that, and then let it pass QA.

Check for other tell tale signs of damage would be my advice.

Although it may have been done by a previous owner for "cosmetic" reasons.

sonicz Rising Star

sonicz

Posted
Posted (edited)

Looks like normal over/under spray to me. Those areas don't have the same paint QA for the final coat as the exterior so some variation between cars is ok.

That said the unpainted washers on your fender bolts aren't original though...

Edited by sonicz
Iron Mike Proficient

Iron Mike

Posted
Posted

Not factory overspray. The engine bays on v specs should be bone stock black. Before I bought my v spec ii I inspected an "immaculate" B.BLUE v spec and when I looked under the bonnet one side of the bay was black and the other side that was being hidden under one of those mechanics scratch sheets was blue!! Shifty mother f***** But anyways, I checked out maybe another 5 v specs and all their engine bays were clean black

GZILAH Explorer

GZILAH

Posted
  • Author
Posted

Hi all,

I spent hours last night googleing 99 Model Bayside Blue engine bays and I couldn’t seem to identify what was the “standard” is! Its driving me crazy!

See the below pics and as example:

Driver side fender & passenger side fender is in a solid blue

Sighting of blue on both sides of the Radiator Support Bar

bonnet01.jpg

No sightings of blue on the Radiator Support Bar

bonnetnoblue.jpg

Driver side fender in solid black

bonnet02.jpg

Driver side fender & passenger side fender is in a light/faded blue

Sighting of blue on both sides of the Radiator Support Bar

bonnet03.jpg

Driver side fender & passenger side fender is in a light/faded blue

Sighting of blue on both sides of the Radiator Support Bar

bonnet04.jpg

Iron Mike Proficient

Iron Mike

Posted
Posted

V-spec I don't have colour coded engine bays. This was a "luxury" update that was introduced from V-spec II onwards. A quick call to Nissan Japan will confirm this for you......or you can spend hours searching Google

BakemonoRicer Grand Master

BakemonoRicer

Posted
Posted

V-spec I don't have colour coded engine bays. This was a "luxury" update that was introduced from V-spec II onwards. A quick call to Nissan Japan will confirm this for you......or you can spend hours searching Google

^ This.

Also, where the panels are bolted onto the chassis (and where you cant see when the bonnet is closed)....this part of the panel will be more of a flat blue colour with only a hint of metallic....as Nissan did this to save costs. Same thing goes for S15. Makes it a smoother transition for the "flat" colour of the engine bay. if they are complete metallic then chances are they've been resprayed.

(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted

Hi all,

I spent hours last night googleing 99 Model Bayside Blue engine bays and I couldn’t seem to identify what was the “standard” is! Its driving me crazy!

See the below pics and as example:

Driver side fender & passenger side fender is in a solid blue

Sighting of blue on both sides of the Radiator Support Bar

bonnet01.jpg

^^ You can rule that one out as that GTR has Nismo Z-Tune Front Guards.

So they would have just painted the whole guard Bay Side Blue.

GZILAH Explorer

GZILAH

Posted
  • Author
Posted

Hi all,

I spent hours last night googleing 99 Model Bayside Blue engine bays and I couldn’t seem to identify what was the “standard” is! Its driving me crazy!

See the below pics and as example:

Driver side fender & passenger side fender is in a solid blue

Sighting of blue on both sides of the Radiator Support Bar

^^ You can rule that one out as that GTR has Nismo Z-Tune Front Guards.

So they would have just painted the whole guard Bay Side Blue.

Thanks for clearing that up mate.

GTR600 Proficient

GTR600

Posted
Posted (edited)

The car attached in my post does have the FACTORY "light/faded blue" on black overspray (that you refer) on the radiator support at the ends where it meets the inner fenders which also has the FACTORY "light/faded blue" on black (that you refer) that runs up the inner fender (where the bolts are) - How do I know - well it is my car :) (The dark light in which the picture was taken does not show it well).

I think what is confusing your results is the light in which the photo's of the cars are taken (that you refer to) and one has aftermarket Z Tune fenders fitted!

CONFIRMING Bayside Blue (V SPEC - 99 Models) SHOULD have the FACTORY "light/faded blue" on black overspray on the ends of the radiator support and the FACTORY light/faded blue on black on the inner fenders. SHOULD BE VERY LIGHT BLUE - slight metallic too (to both radiator support ends and inner fenders)!

I have personally seen over 10 Bayside Blue GTR's and know them inside out!


This should clear up the issue for you!

Cheers

post-77232-0-41912400-1367594296_thumb.jpg

Edited by Buildn
GTR600 Proficient

GTR600

Posted
Posted (edited)

No problems GZILAH

I have attached a photo of a 5,000km R34 GTR 1999 Bayside Blue V Spec engine bay :) note the slight light blue FACTORY overspray on the corner of the radiator support.

post-77232-0-05223300-1367599168_thumb.jpg

Edited by Buildn
GTR600 Proficient

GTR600

Posted
Posted (edited)

Note above picture is a picture of a car for sale in Japan currently

Note the opinions/observations of mine above may not be accurate or correct - please do your own research before making any conclusions or decisions based upon my opinion/observations above.

The world these days!

Regards

Edited by Buildn

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R33 GTR running -9 with no tune

      By Duncan · Posted

      Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Duncan
      Coolant leak?

      By Duncan · Posted

      Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • GTSBoy
      Coolant leak?

      By GTSBoy · Posted

      I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Is it alright to top up with just another green coolant?
×
×
  • Create New...