Jump to content
SAU Community

Is It Normal For Service To Make Your Car Feel Different?

Brandon

By Brandon,
in General Maintenance

 Share

Recommended Posts

Brandon Veteran

Brandon

Posted
Posted

As mention in topic, my car feels slightly more responsive and smoother after,

1) oil change (same brand, Royal Purple HPS, but the workshop used 5W30 instead of the usual 10W40) Not sure if the ones I have been using is HPS or not.

2) spark plug change from platinum to iridium (Denso)

3) oil filter and fuel filter change

4) clutch bleeding (not asked for but they did it cause they suspect my clutch is worn but its not)

Does any of the above affect the response and smooth-ness of the engine much? I told him 5W30 should be fine since its winter but next time I would like to have 10W40 again. Having said that he assured me a good engine can run 5W30 without issues at all unless its blowing smoke.

Advise pleaseeeee. Thank you.

GTR-N1 Grand Master

GTR-N1

Posted
Posted

Variables:-

What was the condition of your old plugs Brandon?

Did you blow through the old fuel filter to see if the residual fuel was discoloured?

Incremental change of old oil to new (and thinner), can result in a noticeable +ve smoothness.

Did the clutch bleed result in extra bite on take-off?

  • Like 1
Greekos Proficient

Greekos

Posted
Posted

you bet, by the time you change your oil most the additives would have gone off bla bla same with coolant, brake fluid and filters, the more you look after your car the better it will run and the longer it will last!

Brandon Veteran

Brandon

Posted
  • Author
Posted

I didn't not get the chance to see the plugs and filter unfortunately.

Dont get me wrong, the car has never given me any issues other than the usual failure due to age/wear. The 2 thing I suspect is the thinner oil and possibly plugs.

The plugs looks clean from previous service but its been awhile since I change them. However, the gap may be too big? I think it's 1mm. Maybe iridium gives a better spark over platinum?

The clutch is still easy to drive being a coppermix. They just bleed it cause they thought the free play was too much. However, it does feel firmer and slightly stiffer.

All in all I'm happy that the car is running smoother. Not saying it's bad before but if the oil is the key, are there any potential issue which can be fatal to the car by sticking with the thinner oil? Or should I go back to 10w40 for my next service since it'll be summer?

GTR-N1 Grand Master

GTR-N1

Posted
Posted

No probs with the current oil with your Kms.

I'd just ask a friend to drive your car whilst you follow it; and you check the smoke coming out of the exhaust. See if there's any more than before.

Brandon Veteran

Brandon

Posted
  • Author
Posted

No probs with the current oil with your Kms.

I'd just ask a friend to drive your car whilst you follow it; and you check the smoke coming out of the exhaust. See if there's any more than before.

Right. Thanks. I'll keep an eye on it this weekend. But driving around yesterday doesn't seem like there is. It'll have smoke in the first gear for once (like cleaning the exhaust carbon) if I floor it but everything else seemed pretty normal.

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

No idea on what sort of mods/engine you have, but flooring it and black smoke = running rich (standard computer does that).

5W-30 seems a bit thin, but once again no idea on what sort of engine you have. I would stick to #W-40 or #W-50.

Brandon Veteran

Brandon

Posted
  • Author
Posted

Just an unopen N1 engine.

Like I said before, I'll make sure its 10W40 for the next service. This time should be ok since its winter and I doubt it'll be much of an issue especially the N1 oil cooler is quite big. Even during summer it rarely goes over 75-80degrees on the gauge. Most times it doesnt even move over the 70

No idea on what sort of mods/engine you have, but flooring it and black smoke = running rich (standard computer does that).

5W-30 seems a bit thin, but once again no idea on what sort of engine you have. I would stick to #W-40 or #W-50.

darksky34 Mentor

darksky34

Posted
Posted

after spark plug change my car started VERY well and idled + drove smoother as well. after a fuel filter change, it felt like it was a little smoother while idling too.

but, always keep in mind the placebo effect!

Ben C34 Grand Master

Ben C34

Posted
Posted

after spark plug change my car started VERY well and idled + drove smoother as well. after a fuel filter change, it felt like it was a little smoother while idling too.

but, always keep in mind the placebo effect!

no shit about the placebo effect! I would seriously doubt a fuel filter change would make any difference at idle, when the fuel requirements are at their lowest.....
Brandon Veteran

Brandon

Posted
  • Author
Posted

Not sure but for RB26, you'd do the pulley/idler/tensioner whatever you call them when you change the water pump. Just to save the time and effort.

I'm about to change my water pump on my stagea for the first time do I need to remove the crank pulley to accomplish that or am I able to avoid it?

badben Enthusiast

badben

Posted
Posted

5W-30 should be fine. It's more when under load that the thinner oil would start to no protect as much as a thicker oil. Nissan oil is 7.5W-30 for 200SX anyway.

32 gtr's are the same. Factory they run 7.5-30. A car with a new rb would be fine. An old engine with 100000 will have bigger clearances thus requiring a thinker oil.

badben Enthusiast

badben

Posted
Posted

Reply to this as well ^^^^^^^

Just an unopen N1 engine.

Like I said before, I'll make sure its 10W40 for the next service. This time should be ok since its winter and I doubt it'll be much of an issue especially the N1 oil cooler is quite big. Even during summer it rarely goes over 75-80degrees on the gauge. Most times it doesnt even move over the 70

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...