Jump to content
SAU Community

Recommended Posts

Hey guys and girls

Hopefully someone can give me a little more guidance here. I have an r32 rb20det track car that I take to Queensland Raceway to drift etc etc..

Basically what happened - I was giving the car a pretty good boot full on the track and came in to cool down a bit. I noticed that there was a little bit of oil coming out of a split in an intake hose onto the tappet covers. When I was driving it I didn't notice any difference in performance or feel. I pulled off the crossover pipe and it had oil in it. I did a compression test with 140-148 results. I installed a catch can today and when I took it for a drive I couldn't get my turbo to reach above 7-8psi. It is usually at about 12psi. There is also a little bit of noise coming from the turbo area.

Turbo seals?

Turbo is no good?

I know I cant really get an accurate diagnosis over a forum, but if anyone can give me some advice it would be much appreciated.

Is my catch can setup going to do its job?

Cheers :)

post-97480-0-87756900-1368691490_thumb.jpg

post-97480-0-81826900-1368691497_thumb.jpg

Edited by argh32
Link to comment
https://www.sau.com.au/forums/topic/425375-rb20det-oil-in-intake/
Share on other sites

Are you sure you couldn't have done a more complex job on the plumbing?

The simple solution is to simply run a line from the ex rocker cover to the catch can, and another line from the catch can up to the turbo inlet. Everything else remains as per factory.

It might then solve your (lack of) boost problem.

if its a track only car and defects ain't a problem, just block intake pipe and pvc valve then run a line from the rocker covers to catch can and put a mini breather on the can..... set up wont work with out a breather.

also if you have an air leak on the intake pipe you can lean out and kill the engine as afm cant read the extra air

But if I only run one line from either the passenger or drivers side cover, won't the other side still be able to put oil into the intake?

If I block that one to stop that will it give the motor less room to breathe under higher RPM?
Like this - http://www.skylinesaustralia.com/forums/index.php?app=core&module=attach&section=attach&attach_rel_module=post&attach_id=220638

That was my train of thought on the catch can situation anyway.

Edited by argh32

if its a track only car and defects ain't a problem, just block intake pipe and pvc valve then run a line from the rocker covers to catch can and put a mini breather on the can..... set up wont work with out a breather.

also if you have an air leak on the intake pipe you can lean out and kill the engine as afm cant read the extra air

Is the PVC valve the inlet on the plenum that I have my red hose on? Sorry for the nub question

^its the valve that's bolted onto the intake plenum

in that picture the intake pipe is still connected. i mean block the line on the pvc valve and the one on the turbo. then put a lil air breather on the catch can and connect up the rocker breather line to the catch can

e911cf73-4186-4004-a775-5511e53b846b_zps

but wont work with out this ^^^

Edited by Dan_J

But if I only run one line from either the passenger or drivers side cover, won't the other side still be able to put oil into the intake?

No. What you are effectively doing is inserting a catch can into the little hose that runs from the ex rocker to the turbo. The can - more technically "oil-air separator" - will condense out the oil vapour (particularly if you fill the can with some steel wool). The in and ex covers are still connect by the "U" hose.

It's PCV - Positive Crankcase Ventilation (PVC is PolyVinylChloride). It only opens under high vacuum (basically @idle), and ingesting a bit of oil vapour at less than atmospheric is not adverse for the engine.

Ok yep, that makes sense to me now.

This morning I blocked off both the PCV inlet and the turbo inlet and my turbo still stayed at about 8psi max.

What should my next move be? Could it just be a lose connection in the intake that I cant find? Would I usually be able to hear the vacuum from a leak?

No. What you are effectively doing is inserting a catch can into the little hose that runs from the ex rocker to the turbo. The can - more technically "oil-air separator" - will condense out the oil vapour (particularly if you fill the can with some steel wool). The in and ex covers are still connect by the "U" hose.

It's PCV - Positive Crankcase Ventilation (PVC is PolyVinylChloride). It only opens under high vacuum (basically @idle), and ingesting a bit of oil vapour at less than atmospheric is not adverse for the engine.

i ALWAYS get it mixed up but, 'yo peeps know what i'm on about' :P

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...