Jump to content
SAU Community

Recommended Posts

Hey guys and girls

Hopefully someone can give me a little more guidance here. I have an r32 rb20det track car that I take to Queensland Raceway to drift etc etc..

Basically what happened - I was giving the car a pretty good boot full on the track and came in to cool down a bit. I noticed that there was a little bit of oil coming out of a split in an intake hose onto the tappet covers. When I was driving it I didn't notice any difference in performance or feel. I pulled off the crossover pipe and it had oil in it. I did a compression test with 140-148 results. I installed a catch can today and when I took it for a drive I couldn't get my turbo to reach above 7-8psi. It is usually at about 12psi. There is also a little bit of noise coming from the turbo area.

Turbo seals?

Turbo is no good?

I know I cant really get an accurate diagnosis over a forum, but if anyone can give me some advice it would be much appreciated.

Is my catch can setup going to do its job?

Cheers :)

post-97480-0-87756900-1368691490_thumb.jpg

post-97480-0-81826900-1368691497_thumb.jpg

Edited by argh32
Link to comment
https://www.sau.com.au/forums/topic/425375-rb20det-oil-in-intake/
Share on other sites

Are you sure you couldn't have done a more complex job on the plumbing?

The simple solution is to simply run a line from the ex rocker cover to the catch can, and another line from the catch can up to the turbo inlet. Everything else remains as per factory.

It might then solve your (lack of) boost problem.

if its a track only car and defects ain't a problem, just block intake pipe and pvc valve then run a line from the rocker covers to catch can and put a mini breather on the can..... set up wont work with out a breather.

also if you have an air leak on the intake pipe you can lean out and kill the engine as afm cant read the extra air

But if I only run one line from either the passenger or drivers side cover, won't the other side still be able to put oil into the intake?

If I block that one to stop that will it give the motor less room to breathe under higher RPM?
Like this - http://www.skylinesaustralia.com/forums/index.php?app=core&module=attach&section=attach&attach_rel_module=post&attach_id=220638

That was my train of thought on the catch can situation anyway.

Edited by argh32

if its a track only car and defects ain't a problem, just block intake pipe and pvc valve then run a line from the rocker covers to catch can and put a mini breather on the can..... set up wont work with out a breather.

also if you have an air leak on the intake pipe you can lean out and kill the engine as afm cant read the extra air

Is the PVC valve the inlet on the plenum that I have my red hose on? Sorry for the nub question

^its the valve that's bolted onto the intake plenum

in that picture the intake pipe is still connected. i mean block the line on the pvc valve and the one on the turbo. then put a lil air breather on the catch can and connect up the rocker breather line to the catch can

e911cf73-4186-4004-a775-5511e53b846b_zps

but wont work with out this ^^^

Edited by Dan_J

But if I only run one line from either the passenger or drivers side cover, won't the other side still be able to put oil into the intake?

No. What you are effectively doing is inserting a catch can into the little hose that runs from the ex rocker to the turbo. The can - more technically "oil-air separator" - will condense out the oil vapour (particularly if you fill the can with some steel wool). The in and ex covers are still connect by the "U" hose.

It's PCV - Positive Crankcase Ventilation (PVC is PolyVinylChloride). It only opens under high vacuum (basically @idle), and ingesting a bit of oil vapour at less than atmospheric is not adverse for the engine.

Ok yep, that makes sense to me now.

This morning I blocked off both the PCV inlet and the turbo inlet and my turbo still stayed at about 8psi max.

What should my next move be? Could it just be a lose connection in the intake that I cant find? Would I usually be able to hear the vacuum from a leak?

No. What you are effectively doing is inserting a catch can into the little hose that runs from the ex rocker to the turbo. The can - more technically "oil-air separator" - will condense out the oil vapour (particularly if you fill the can with some steel wool). The in and ex covers are still connect by the "U" hose.

It's PCV - Positive Crankcase Ventilation (PVC is PolyVinylChloride). It only opens under high vacuum (basically @idle), and ingesting a bit of oil vapour at less than atmospheric is not adverse for the engine.

i ALWAYS get it mixed up but, 'yo peeps know what i'm on about' :P

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...