Jump to content
SAU Community

Recommended Posts

  • Replies 269
  • Created
  • Last Reply

Top Posters In This Topic

Just a quick question, do you plan to stop producing these in the near future or will you still be producing them on a per order basis?

cause i want one! i'm just still saving for it! :rofl:

Anyone else still interested? Fitzy has his custom made one coming soon, with a screen around 4 times the size of the original one! I can take pics if anyone is interested!

Impakt

4x the size of the original screws?? What is the purpose of this?

Hell yeah. I'd like to have a look at it. It'll be interesting to see.

I am very interested but have an HR31 and would need to be wired into the ecu loom as they do not have an consult pot :) could you do a wiring diagram of the wires? or do you know if a connector could be wired in?

I may still look at getting one and cutting the consult port off and wiring it directly into the ECU loom. I know the TPS position wont work and a few others but I just want this type of gauge with oil temp, water temp fuel presure in one unit.

Update: Just got a call from a VFD screen supplier. These are the same type of screen used in the Apexi S-AFC, and AVC-R etc.

The replacement screen is $160 + 60 day wait. This is how much i get them for. If anyone is interested, or knows where to get them cheaper please PM me :)

Impakt

Got mine a couple weeks ago and installed it in 5 minutes, down in front the ashtray angled up. Works great - I have to try the datalogging software this weekend.

About the oil press/oil temp/fuel press, maybe you could include a couple of analog inputs for things like these, that don't come from the ECU. Just a thought.

just reading these posts

r31 and z31 dont have consult. it was developed r32/z32/s14 onwards

i am currently making an interface for the r31 (6802 processor has no serial connect interface, but imports HR31 use 6303 which does so it is possible to get consult implmentation on that). one of my many projects. also trying to nut out TP values for most ECUs to do accurate maptracing (R32 i have done, R33 to come) along with nutting out daughterboard for R33 (its difficult but not impossible)

you can pull maps from any ECU with the right software. ideal for putting in the chips of daughterboards because the MCUs contents inside ECUs are locked protected otherwise

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...