Jump to content
SAU Community

Recommended Posts

Made up a second catch can/windscreen washer bottle and also a power steering reservoir.

I plan on running two catch cans, one on the drivers side retuning to the PVC and to the sump and the

second on the passengers side returning to the inlet of the turbo and the sump as well.

I'll be able to hide the boost control valve and windscreen washer pump in the cavity under the tank.

IMGP2521_resize_zps0be3bd9d.jpg

IMGP2522_resize_zps5e9d7e18.jpg

IMGP2523_resize_zpsf0aa7a8d.jpg

IMGP2520_resize_zps04013510.jpg

IMGP2527_resize_zpsdada68f1.jpg

  • Like 2
  • 1 month later...

Small update, welded up the intake pipe and return from the synapse diverter valve to the intake.

Don't think I will use the air box I made.

IMGP2530_resize_zps1bd33709.jpg

Also trying to work out a bonnet hinge, going to make some in the style or R33 boot hinges.

These are just some pieces of flat bar to work out the lengths of the links and where the pivot points will be.

Should be able to make the bonnet swing up 90 deg.

IMGP2532_resize_zps55e12ca2.jpg

IMGP2531_resize_zps3276425c.jpg

IMGP2533_resize_zps1eba5a56.jpg

  • Like 2
  • 2 weeks later...
  • 1 month later...

Bit of an update, brought some wheels, crossfire D-spec 18x9.5 also brought some hardrace rear arms. Started extending the sump

and filling in the bottom of it to hopefully help oil return.

IMGP2568_resize_zps578e42e8.jpg

Little bit of stick out.

IMGP2559_resize_zps0ca0ccd2.jpg

IMGP2547_resize_zpsaf299f8c.jpg

IMGP2552_resize_zpse2da0b54.jpg

IMGP2572_resize_zps49e918ba.jpg

IMGP2576_resize_zps81be60c0.jpg

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...