Jump to content
SAU Community

Setting Up Adj Actuator

R TUNE

By R TUNE,
in Engines & Forced Induction

 Share

Recommended Posts

R TUNE Mentor

R TUNE

Posted
Posted

hi guys,

my last boost controller started failing so me and my tuner decided to mod the stock actuator to make it adj.

my target psi is 14psi and using the stock actuator it held at 11psi.

my question is how much shorter/ longer do i need to adj it to reach my target psi. i have it currently set at 1 cm shorter than the stock length.

mods are as follows

45v4 turbo,

3 inch turbo back exhaust

cam gears

blitz fmic

nistune ecu

engine is a RB20DET.

last power out put was 165rwkw with boost topping at 16 psi by 4000rpm and dropping to 12 psi by 7500rpm.

regards

brentton

Link to comment
https://www.sau.com.au/forums/topic/427553-setting-up-adj-actuator/
Share on other sites
MrStabby Grand Master

MrStabby

Posted
Posted

If you add more preload it will make the boost curve worse, like 20psi dropping to 14. Adjusting the preload won't change the point at which the diaphragm in the actuator operates.

Thats the opposite of my understanding. The gate operation is a fight between the spring and diaphram. Increasing preload has the effect of increasing the force developed by the spring. The force that the diaphram produces depends on the boost. So if the spring force goes up, you need more boost to open the gate.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Spring force isn't adjustable, it is a set force/mm.

If you decrease the length of the actuator arm you are forcing the spring to close more before the flap opens. It works, but not as well as replacing the spring with a stiffer one, and you could reach a point where the flap doesn't open enough to bleed boost off in the top end. (boost spike)

Try it out, just make sure you have a good gauge, I have seen too many that read 3-5psi out.

I would be hitting up Hypergear for a 14psi actuator. Install and forget.

Ben C34 Grand Master

Ben C34

Posted
Posted

From Hypergears thread, page 397

If you over pre-load you will get boost spike and then taper. Try to have it hold one consistent boost pressure off the spring only.

That actually looks OK. its making 150kw @ 4000 rpm which isnt THAT bad for a 200k+ auto. Have a fiddle with preload and just check VCT as said.

pg 398

Its extremely important remembering to preload the actuator as the tuner's tuning. keep on preloading if are seeing boost tapering off before the desired level. It might be 5mms or could be 15mms, the more you load it the higher up top boost level it will hold, more boost makes more power.

GTSBoy Grand Master

GTSBoy

Posted
Posted

Superben, that quote from page 398 is to be read as "adding preload stops the boost tapering off at the top end".

The corollary of that, and part of the page 397 quote is that it also tends to cause a spike as the boost comes on, which is not always (or even often) desirable.

bananaweesle Contributor

bananaweesle

Posted
Posted

run a Turbosmart or Kando actuator they have springs inside that can be easily changed and the boost dropping of problem nearly disappears. the only reason boost drops of at higher rpm is because the pressure in the stock exhaust manifold is so high the gate actually gets pushed open and is unable to close. Once open with standard actuators and high boost the actuator nearly becomes useless as at about 4500rpm the actuator is forced open and cannot shut.

MrStabby Grand Master

MrStabby

Posted
Posted

Spring force isn't adjustable, it is a set force/mm.

You are saying the force produced by the spring can't be referred to as "spring force" - I disagree. Force/mm is not a sensible term, you should say either force/distance or if you're expressing it in units, use units both sides, eg. Newtons/mm. This property is known as the spring constant (or rate, or spring rate). I agree that spring constant is not adjustable.

OP - try increasing the preload a bit more, and see how it performs. If its sucks, get something else.

MMM interesting, i have been suggested to remove the ball and spring out of the boost controller and run it like that. Any one have experience with this.

If its one of those $20-30 boost controllers then removing the spring and ball makes it a very expensive bit of pipe.... :)

Kane_R32 Experienced

Kane_R32

Posted
Posted

MMM interesting, i have been suggested to remove the ball and spring out of the boost controller and run it like that. Any one have experience with this.

You do realise the ball and spring are whats needed to "trick" the actuator into creating more boost? So removing both well render the boost controller useless and you will run wastegate pressure.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

No, they have a small bleed hole in the side, so it will actually run as the stock turbo does, bleeding a little of the pressure off to raise the boost. How much boost depends on the size of the bleed hole and the actuator spring.

Kane_R32 Experienced

Kane_R32

Posted
Posted

I would like to see what level of boost increase you would see though. I don't think the 1mm bleed hole would let out nearly enough boost pressure, compared to if the ball and spring was there to restrict flow, and increase boost.

  • 2 months later...
Blackkers Experienced

Blackkers

Posted
Posted

Hey guys sorry for bringing up an old topic. I'm having trouble with an EBC + RB20 actuator. max boost set to 1 Bar. The trouble is I can't find a good balance between response and overboosting with the EBC GAIN setting. I think it's because of the difference between my boost setting and the hardware setting (wastegate pressure)

Has anyone used the Kinugawa actuators on an RB25det highflow? using standard comp and turbine housing. They sell a 1Bar spring that would be perfect.

heres a link: http://www.ebay.com.au/itm/Kinugawa-Adjustable-Turbo-Wastegate-Actuator-Nissan-Skyline-RB25DET-R33-/281163573117?pt=AU_Car_Parts_Accessories&hash=item4176a7a77d

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
    • GTSBoy
      R33 GTR running -9 with no tune

      By GTSBoy · Posted

      So while the second sentence is completely correct and the whole point of the conversation, the first sentence bears consideration. If this bloke is just hoping to throw big turbos on and drive it around, because there are no helpful facilities at all in his tropical paradise** then he likely has zero chance of even knowing what the TP is on the last column in the stock maps, let alone know whether the ECU is operating anywhere near it or past it. So the point is very very moot. And, per what I said before, at stock boost on those turbos, you may well be off the end of the map. **I'm just back from Vanuatu, so I know exactly what small Pacific nations can be like wrt paradise without requisite facilities. But it's not even that simple. I put a high flow on my car and had to drive it around without a proper tune because of the lack of opportunity*** to put the bigger AFM and injectors into it to allow it to be tuned. I had to turn the boost down to less than I had before, and back off the boost controller's ramp, because it was exploring parts of the map that it didn't drive in before, and really couldn't access for tuning on the dyno either, and so was pinging. It was still well within the last column, because when I first**** set up the Nistune on the Neo I rescaled all axes of the maps to give some more space to explore. ***Family dyno was broken ****This was 13 years ago, and the TIM thing wasn't a thing then and so TP would definitely grow when pushing past the stock tune's limits.
    • joshuaho96
      Squeaking clutch/throw out bearing

      By joshuaho96 · Posted

      Yep, this bit another local owner. I caught it before putting the transmission back into the car, what I noticed was the pressure plate fingers weren't flat and even. It's more obvious with the pull style clutch because the throwout bearing ring was visibly not flat once everything is put together. Nismo should really update their instructions to call out this specific detail. I'm not even sure the clutch as-shipped orients everything properly.
×
×
  • Create New...