Jump to content
SAU Community

Recommended Posts

Perhaps you have a blocked cat and this is what the sensor is telling you?

Wouldnt expect it to just all of a sudden block and cause the car not to start at all.

The sensor just unscrews from the cat. Mine still works (AFAIK anyway)

The sensor only makes the warning light come on on the dash, it doesn't send any signal to the ECU.

I changed my fried cat and couldn't get the sensor out so I just cut it and blocked the hole in the new cat with a bolt.

The light comes on and goes out when the car is started.

Your cat may be blocked, or your not starting problem could be totally unrelated...

Try removing the cat and starting the car, if it starts, smash the guts out of your cat, reinstall and buy a new cat ASAP.

Same problem with my car .

My car runs and drives fine tho,but the car wont idle for more than 5mins even after a drive and the owner told me the cat temp is not plugged in thats why its causing it to automatically shutdown or theres more to it than that? & the temp light is always on.

thats the light thats always onpost-112075-0-61525800-1372779439_thumb.jpg

any help would be great.

Yes that's my understanding of the R33 too.

In an R32 the cat over temp light is the check engine light so it does connect to the ecu for that purpose.

Can't understand people hacking wires.

Under the passenger seat you can UNPLUG the cat sensor wiring, no need for butchery.

Fit a grommet in the floor pan hole and it's looking good.

Well mods on the

-Full 3" exhaust

-Fuel pump

-pod filter

-TS boost T

stock everything.

idles fine n drives n sounds fine! But if i start the car let it idle it just won't idle for longer than 5mins its the same even after a drive it automatically turns off the car

But all electronics are on all i have to do is turn the key to the right n it starts again fine.

Try hard wiring the fuel pump using the 'how to', most aftermarket pumps don't like the low power supplied by the factory fuel pump controller. To test it you could run a temporary wire to the battery...

What pump did you install?

well this morning i started up to see how long it will run for

it ran for 12mins n could of kept going so believe it or not it didnt happen today

when i came back from work,it usually runs for a bit n shuts down this time it ran for a while till i got bored like wtf :closedeyes:

i bought the car with the fuel pump already installed.the last owner put it in and he said it holds up to 600hp i believe

Brand- no idea

i'll ask for details coz he said he would fix the shutting down problem anyway.

since he said its cat being unplugged,now i know its not im not happpy :verymad:

Reset the ECU. Quick to do and sometimes solves the problems.

Disconnect battery (negative terminal), Hold foot on brakes, flick lights on and off etc, basically just do whatever you can to drain any residual power.

Wait for 10 mins or so then plug the battery back in and start the car, go for a drive etc.

I'm not sure if the 10 mins of sitting is necessary but just to be sure

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It doesn't look like there's a lot of options out there these days, and what's out there is performance oriented aftermarket stuff (with the GTR markup) I wonder if there are other cars with similar springs, after all its just a matter of length, diameter and stiffness. Alternatively, I did see coil spacers. Probably not the best option, but could be serviceable too.  
    • Final thought for now. Obviously the reason I was in there was to check everything is OK cooling wise, pull out the radiator to flush it etc, but I have to say the factory has done a hell of a lot of thinking about air management in a way they never did back in the R chassis days. The Redsport/400rs have (from engine forward) 2 large shrouded fans - radiator (incl AT cooler) - AC condenser - Intercooler Heat Exchanger and Oil cooler. There are shrouds and foam around everything to keep it pretty well sealed, which is good in that they have it sorted from factory, and bad in that I can't make any meaningful improvements there. The second red sport pump water pump is mounted in front of the rad in the airflow, so I will see if there is somewhere else I can stash that (unlikely, it is tight in there). The horns which are also in the rad airflow will be moved somewhere else, and hey who needs 2 when 1 would work For track days, I can also remove the lights which would block some airflow. Factory has already taken the smart option of ducting all air that went through the oil cooler down and out of the engine bay. This pic is taken from below looking up, so air comes through the cooler at the top of the pic then hits the shroud and is directed down and out of the engine bay through the engine bay lower cover Which of course is good for oil temps, but doesn't help the rad as it diverts 10-20% of airflow away So, no big improvements to be made here, I'll flush the rad out and put it all back together.....    
    • It looks so incredibly busy in there! 馃槷 
    • Next..... That escalated quicker than an Elon and Donald break up! I'll post up a specific DIY for radiator removal on these, but all I'm saying is that if you get a workshop to change your radiator for any reason and they give you a $1000 bill for it, go and hug them and thank them for not charging all the hours it took.....what a bastard of a job. I'll make some adjustments as I put it all back for faster access in the future, but it was a nightmare.
  • Create New...