Jump to content
SAU Community

Recommended Posts

Possibly a very easy question but never dealt with defects before.

Bought an unregistered car with a red sticker. The paper work that came with it didn't have any of inspection stations ticked for example AIS, AUVIS, etc

The only thing ticked was: Full inspection and Light vehicle

As the car's rego has lapsed, it will need a blue slip. Is that all is needed to get the car on the road now?

A lot of people can do the inspection http://autocollective.com.au/category/defects/what-to-do/ - this page suggests looking here for people who can do it http://www.rta.nsw.gov.au/cgi-bin/index.cgi?fuseaction=inspectionstation.form But, I think this is only for a e-safety check (pink slip)



Infact ( & this is just a free plug), just last night a bunch of us where down at Japlink / JLM in Rydalmere for a SAU members tech night to talk about engineering certs,compliance & more.

Great set of guy's, super friendly and will tell you straight up what you need to do and will try to help you as much as possible if they can. Try giving them a call.

Number on their website is 02 97160857

what type of car?

if it is a grey import(im assuming it is), you can no longer get them cleared at pink slip stations(ais).

they all have to go to a blue slip(auvis) station to be cleared.

so, either way, its getting a blueslip.

as mentioned, just had the tech night at japlink, great bunch of guys, and can do blueslips ;)

so, if its more convenient at a place near your work, so be it.

be sure to write a letter with your name, lic number, car vin, leaving from, going too, reason, and expected times if youre driving.

rms states you can drive for rego purposes, cops think you should tow it.

so, if its more convenient at a place near your work, so be it.

be sure to write a letter with your name, lic number, car vin, leaving from, going too, reason, and expected times if youre driving.

rms states you can drive for rego purposes, cops think you should tow it.

Red defect + Unregistered.

Yeah, I'd be towing it to, especially to be able to get it to a place that will look after it more like JLM.

Hypothetically speaking, What if I were to remove my plates? Cops won't know the car is red stickered and I can say I'm driving to the nearest blue slip place, which I am, to get it rego'd

According to this link: http://www.rta.nsw.gov.au/registration/unregisteredvehicles/index.html there shouldn't be a problem

The car is reverted back to stock, it's no longer a defect, according to me anyways.

Edited by rorii

Hypothetically speaking, What if I were to remove my plates? Cops won't know the car is red stickered and I can say I'm driving to the nearest blue slip place, which I am, to get it rego'd According to this link: http://www.rta.nsw.gov.au/registration/unregisteredvehicles/index.html there shouldn't be a problem The car is reverted back to stock, it's no longer a defect, according to me anyways.

This is also correct! you may drive to the closest inspection station (to your home address)

Edited by Frosty

To drive an unrego'd car you need to obtain a permit. No registration is no registration.

You won't be covered if you hit any car or person. Paying the tow fee or rental fee for a trailer will be cheaper n safer.

My understanding of the ,drive to the nearest station for a slip, is for pinks only. It's for cars just out of rego who still have the 3 mouths to get a pink slip. That's when you can shoot up the road to get a pink.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...