Jump to content
SAU Community

Recommended Posts

Step 1. Undo the clamps on either side of this U-Shaped hose, then remove the hose.

UHose.jpg

Step 2. Undo these 2 screws, it will allow you lift up the intake pipe giving you more room.

2nuts.jpg

Step 3. Loosen the 2 adjustable clamps on the hose connecting to the plenum, also the other small one seen in the picture.

plenum.jpg

Step 4. Disconnect the loom plug (may vary in appearance). Then just move 2 disconnected looms off to the side. You don't have to remove the 2 circled screws.

loom.jpg

Step 5. There are 8 allen screws to undo all the way along the plastic cover as circled below. Once you have removed them all you can then slide out the plastic cover.

rockercover.jpg

Step 6. Once you have removed the plastic cover you'll see the lead pictured below, with 6 looms connecting to the top of each coilpack, undo the looms that connect to the top of each coilpack. Then remove the small screws that hold the length of cable in place and remove it.

(Coil Pack Lead)

somecable.jpg

nocover.jpg

Step 7. Now, at this stage you will see the top of each coil pack, I pulled out the whole cradle and coil pack as described next but you dont have to that. You can just remove the screws that hold each coil pack in. This how to pull it all out.

Unscrew the gold/bronze bolts that hold the coil pack cradles in place. There is about 6 or 7 of them. Once they are removed you can pullout the coilpacks and cradle to see the spark plugs underneath.

(Top of Coil Packs)

noloom.jpg

(Coil Packs and Cradle)

coilpacks.jpg

Step 8. Now that you can see inside, it is recommended that you spray some compressed air inside to clear/dislodge any crap that may fall into the combustion camber once you have taken out the spark plugs. Now remove the spark plugs and put in the new ones!

Step 9. Put it all back together.

Edited by Shane
  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/42819-rb25det-changing-the-spark-plugs/
Share on other sites

  • 4 weeks later...
  • 2 months later...
  • 1 month later...

had the plugs in mine done a few weeks ago. Used NGK iridiums to suit rb25det.

Took in for a tune the other day and had problems. Apparently I should have used NGK iridiums to suit rb20det as they run cooler. She runs nicely now and the plugs are cheaper!

  • 9 months later...

anyone know if you just pull the coilpacks straight out once the two screws are removed?

seems like the pack is still attached to something underneath and i'm not game enough to put too much force into pulling it out without knowing.

had the plugs in mine done a few weeks ago. Used NGK iridiums to suit rb25det.

Took in for a tune the other day and had problems. Apparently I should have used NGK iridiums to suit rb20det as they run cooler. She runs nicely now and the plugs are cheaper!

Hey so which one should you use?

rb20 or rb25 sparks? should you also get it tuned after the installing the new sparks?

I love this tutorial.

Found it over a year ago, made it into word doco format.

Printed it off in colour and make sure it's around everytime i change em juts to be sure.

Thanks matey !

Awesome job!

Used the changing oil one for awhile but thats piiiss easy so don't need it now.

(but not easy if you've never done it before, which is where i was awhile back)

The best thing is, changin oil and spark plugs must be 80% of what a 'service' is and you never know exactly what they're doing........so get in there guys and do it yourself.

  • 4 weeks later...

Would the author of this tutorial please add:

Loosen the plugs, BUT before removing them, blow the area thoroughly clean with compressed air.

Can't believe people still pull dirty plugs and wonder why they suddenly develop a miss after dislodging crap into the combustion chamber.

Regards.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...