Jump to content
SAU Community

Recommended Posts

hi, hope it hasnt been covered before (cowers) simple question, can r33 rb25detpistons be used with a r34 neo head? ive noticed that the r34 pistons have valve reliefs so im bit concerned about piston to valve clearence and an increase in compression? thoughts? comments ? (no nasty ones please)

Link to comment
https://www.sau.com.au/forums/topic/428525-r33-pistons/
Share on other sites

thanks guys, youve given me a bit to think about

. . picked up a 34det neo dirt cheap and (also havea 33 bottom end) it has a damaged #3 cylinder and just working out my options for using what i got

it had swallowed a small bolt which made it run on 5 and the guy who owned the car drove it for three months like that. .

Link to comment
https://www.sau.com.au/forums/topic/428525-r33-pistons/#findComment-6925634
Share on other sites

Use the Neo bottom end. Buy pistons. Sell R33 stuff to someone else. Profit.

wildo that , originally was told number 3 was dead and was (possible detonation damage) cos the owner was running it on 91 ulp

owner needs shooting as this motor still has factory hone marks on the bores

if anyone here has some low k (stock size) 34 pistons in good condition please pm me as the internals of this motor are in otherwise mint condition and wouldnt take much to get it going again

Link to comment
https://www.sau.com.au/forums/topic/428525-r33-pistons/#findComment-6925674
Share on other sites

Neos use RB26 rods, which are a different length to older 25 rods (I'm pretty sure....).

Nope.

RB25 non NEO and NEO and RB26 share the same con rod length.

NEO uses the same 'stronger' rod as the 26 though.

OP - I have a full set of 34 NEO pistons and rods in excellent nic for sale, unless Simon still wants them?

Link to comment
https://www.sau.com.au/forums/topic/428525-r33-pistons/#findComment-6925894
Share on other sites

kitto beat me to it.

neo rods same length as non neo. As is the pin height on the pistons. in fact the neo piston and non neo piston share all the same dimensions but the neo piston has more cooling passages under it where oil is squirted. its probably lighter also but need to weigh some to confirm.

the difference in compression is all in the head.

Link to comment
https://www.sau.com.au/forums/topic/428525-r33-pistons/#findComment-6929275
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...