Jump to content
SAU Community

Recommended Posts

Hey all :)

I have a problem with my skyline. Only occasionally I will start it and begin to drive.. then when I'm accelerating it seems to lose power and slightly "bunny hop" the bunny hops are not aggressive. it just doesn't seem to be able to get to higher revs. It does happen when it's cold but by the time it's warmed up it still has the problem.as I said it only does it every now and again. Does anyone have any idea what could be wrong?

Link to comment
https://www.sau.com.au/forums/topic/428944-intermittent-problem-with-r32-gtst/
Share on other sites

No mods except for a coke can in the blow off valve (bought like that) :P

Don't know the service history from previous owner. Has had a complete full service. Was happening before I recently got it serviced.. mechanic changed the fuel filter and spark plugs (thinking they were the cause) but problem still persists

It happens at any revs. It happens whenever I accelerate

  • 1 year later...

Found this thread and am bumping it because I have a similar problem. I'll describe it in more detail though.

This happens occasionally, and only early in any drive if it does. Not like right out of my garage but 1 or 2 minutes in. I will probably happen at a frequency of about once every 3 times i drive the car.

Once it happens it will happen until i let it sit out of boost for a while and it will be ok. I even did 5 runs at autocross after this, problem did not crop up.

How violent it is depends on how much throttle i'm using. If I hold it down as i'm trying to accelerate and not let it if it reminds me as if someone who is just learning to driving a manual is driving the car. Off-boost it doesn't do this. It only does it at RPMs in which the turbo is building or holding pressure.

Same recommendations? I don't have another AFM to try otherwise I would but I could install my powerfc and put in a Z32 AFM.

I had an r32 gtst back in 2004 which would do that, the car would lurch back and forth violently under acceleration. Turned out to be a really dirty fuel filter, wasn't allowing sufficient fuel to the rail so the car was suffering fuel starvation. Upon reflection I'm surprised I didn't destroy the engine, must have been running ultra lean during those periods.

I had an r32 gtst back in 2004 which would do that, the car would lurch back and forth violently under acceleration. Turned out to be a really dirty fuel filter, wasn't allowing sufficient fuel to the rail so the car was suffering fuel starvation. Upon reflection I'm surprised I didn't destroy the engine, must have been running ultra lean during those periods.

Did it do this all the time or only occasionally like it's doing for me?

I would think if it were a fuel filter it wouldn't just stop and be fine for hours.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...