Jump to content
SAU Community

Recommended Posts

Seem to have a problem with fuel on the pressure side of the system draining back to tank when the car is switched off and left for a while. I am away from work for 7 days and when I come back it takes a bit to start the first time and recently it runs a bit rough for a bit after the car is started. When driving it has a small miss, but it goes away fairly quickly

I believe it is a problem with the fuel draining back to tank and just wondering if anyone has found anything similar and knows why it might be happening

I was away for nearly a month once and the car idled horribly (Sounded like it had a super lumpy cam) for about 5 minutes. But usually when I'm away for a week its not as big a problem as the issue goes away quickly and its not so bad if started daily, but I would like to fix it. I've found check valves for fuel systems but most seem to be for Carb and low pressure fuel systems. I dont really want to start forking out for braided lines and JIC fittings etc for the fuel system, would rather a barb fitting check valve etc

Just after anyone who has had a similar problem or is it just something you have to live with?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/429788-fuel-draining-back-to-tank/
Share on other sites

changed your fuel pump? or maybe the internal check valve has failed..

stock pumps have a check valve as do some aftermarkets. I know for a fact that bosch 040 has no check valve and I had hard-starting problems as soon as I put one in. had to pull it out and put a speedflow check valve in just above the pump and it has started first time every time since then.

Have a Nismo Pump, and have done for about the last 4 years or so. Never had the problem to start with

I did change the FPR with another stock one a while ago, just cant remember quite when. (if it was before or after the problem started)

I have another rail and FPR with new Nismo 740's going on soon


Might disconnect the return line with the car off and see if anything comes out of the FPR at some point

Do the Nismo pumps have a built in non return valve in the pump? Or is it the little part that comes with the kit? I played with it a bit and decided it wasnt a check valve so I didnt put it in. Will have to see If I can adapt a fuel pressure gauge in there. Think I can, have an old gauge from work at home just have to get some barb fittings and chuck it in somewhere

Your talking about fuel pressure dropping off to quickly when the engine is turned off? or is the FPR supposed to keep a small amount of fuel in the pressure side? I imagine the FPR drains through an orrifice when the car is turned off to drain the pressure out of the system, but having never had a fuel pressure gauge in there I'm not 100% sure on what it should do

Thanks

I think you will find your problem is something else entirely man, I've got a fuel pressure gauge on mine and the pressure begins draining off almost immediately after switching the car off. Takes less than 5 minutes or so to drain off all the pressure. I don't have issues starting no matter how long the car sits for. Regardless, surely you prime your fuel pump before starting?

Yeah it seems like fuel drains out of the injectors and then when starting theres an air lock in the injectors or something.

Might pull the fuel pump out when the car is off the road for a look. Might all come good with new injectors and the other fuel rail and FPR yet

  • 1 month later...

I'll update this thread

I pulled the rail off today and noticed on the inlet side of the fuel rail, pretty much all of the fuel had drained back, Then pulled the return line off the fuel regulator and there was fuel and a little bit of pressure. Some air and fuel came out, had to block it off.

My fuel tank doesnt really pressurise anymore so not real sure if this is normal or not. Car had been sitting in the shed for about a week before I pulled the rail off.

If this is normal I think I wont really worry about it I think. Have another rail with new injectors and fuel reg on it so something there might fix it anyway lol

Not sure if the fuel damper could be the issue, seems unlikely but dont know much about fuel dampers

Edited by 89CAL

Sounds normal to me. Unless you have a check valve in your feed line, there is nothing holding pressure there. Whereas in the return line, your pressure reg will hold some pressure.

Not sure how correct I am, but that sounds right to me. My return line usually has a little bit of fuel in there when I pull it off.

Yeah the only odd thing I thought was that the little bit of pressure I described was on the tank side of the reg. But this may just be how the fuel line is run (fuel gravity feeding back towards the front when a line is removed)

Yeah I'll just live with it I think, it's not that annoying unless I havent driven the car for a while

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...