Jump to content
SAU Community

Recommended Posts

Ppls.. ;)

My cars just been resprayed. I pick it up Thursday. ;)

I poped down today to check it out without its windows and lights in.

It hasn't been buffed or checked over yet but from what I can tell it didn't look like it needed a buff.. Its soo damn shinny. The Colour is such a rich black.

Looks awesome.

So thats got me thinking.. What Polish?

Should I use a Wax type polish or the other type of polish like NuFinish or 5 Star?

http://www.nufinish.com/

http://www.5starshine.com/

I've used NuFinish on a different car and it did keep the water beading for much longer than the usual car polish. It was also easy to remove bird crap.

BUT.. does it really protect the paint?!?!

Link to comment
https://www.sau.com.au/forums/topic/43001-car-just-resprayed-which-polish/
Share on other sites

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Pinnacle Souverain, S100, Poorboys or Clearkote Moose Wax...

Good luck finding them here though, I order mine from the states.

You can get S100 from Harley Davidson dealers in Australia, so that's probably the best bet for you.

I use Meguires Gold Class. I use to buy it from the US when I was travelling over there with my old job (it cost me ~$6US) Luckly I haven't run out of it yet. But when it's time to get more I think I'm up for mid $30's.

I would highly recommend the Meguires Gold Class.

Clearkote Moose Wax is the goods, if there's an aussie distributor I'd get it from them in a flash, but right now i'm restricted to when a friend goes over tot he US only.

Oh and buy a clay bar... mmm clay bar.

You can order Clearkote products online:

www.clearkote.com

I have ordered from Everett Glass (clearkote's head honcho) before and I can recommend NOT to get it shipped via surface mail... It took MONTHS to arrive. Get it sent via airmail.

I also suggest to purchase the following:

Clearkote QuikShine (admittedly Meguiars QuikShine is also very good), Vanilla Moose Wax and Moose Wax.

Order of application:

1. Wash car with Dawn dishwashing liquid or other akaline based detergent. This will cut right through all existing waxes and remove buildup of product. (only do this every third waxing application)

1. Clay Bar (if needed)

2. Vanilla Moose Wax (removed surface marring (swirl marks))

3. Quik Shine

4. Moose Wax (protectant and gives that deep, wet look to your paintwork)

5. Quik Shine

Spend a day doing the above and your black paint will look like a billion dollars. Depending on whether you garage your car, park it under trees, near the ocean, etc... That will protect your car for about 3-6 months. It won't stop swirl marks however, so you will have to do it more often if you want your car looking swirl-free all the time.

And if you don't like the products, PM me and I'll buy them off you.

These are PROFESSIONAL car care products, not consumer targetted, mass-marketed products like Meguiars and Mothers.

As for towels and sponges etc... Stick to microfibre towels for drying, and pure lambswool mitts for washing the car, constantly wringing it out and spraying off all the contaminants so you don't rub dirt over your paint which will obviously scratch it. Goto http://www.autopia-carcare.com for great detailing products. Their concours range of towels are HEAVEN! ;)

Actually just looking at Clearkote's website, they have released a new Carnauba Wax... Everett gave me a small sample of some new wax he was about to release in my last order, I wonder if that's the one...

Whatever it was, it was excellent ;)

wow and here i was thinking the only thing merli ever cared about was the feel of soft supple leather on his naked skin...

-joel-.... you're on street commondoors aren't you? I recognise you nick from a thread that's sorta skylines vs commondoor on there.

a clay bar i well its a bar of clay, you rub it on your car and it takes all the dirt off without scratching the paint/polish. Its THE best way to remove grit, dust particles that have sorta gotten intot he polish etc, that usually don't come off with the pre wash.

Moose Wax - $30 (Quart... This is enough to wax your car about 20 times)

Vanilla Moose - $12

QuikShine - $38 (Gallon... This will last you for AAAAGES)

--------------------

Total - $80

Therefore, I suggest you get that "Show Special for $60" at the bottom of the Order Form Page... Great value!

Shipping is pretty expensive though... But what's $150 (all up) when you've just spent thousands on a top quality paint job?

Oh, I've never had a car resprayed before, but I think you have to let the paint cure for a few weeks? So don't go washing it or something until the paint is completely cured. Ask your spray painter. Depends on how the car was baked as well I think.

And since it's a new paint job, I think you can skip the clay bar

Guest RedLineGTR

Okay first of all thoe a paintjob is baked in an oven it still has to breathe and the paint to form its hardest form this takes a week or so. The only polishes you can use are "pure" polishes I believe meguires sell these types but don’t have too much info on other brand. My 2 cents

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...