Jump to content
SAU Community

Recommended Posts

All parts from a 1994 Series 1 R33 gtst 4 door I wrecked, cheap cheap!!

Many parts are pick up only unless stated otherwise so read the description carefully.

Sedan boot lid $20. Pick up only.

IMG_9993_zps1f1c63b7.jpg

Rear hubs $20 each (includes uprights). Pick up only.

IMG_9057_zps175ae95c.jpg

Front and rear sway bars $20 each. Pick up only.

Rear cradle (bare cradle) $20 each Pick up only.

Non abs brake master and booster $20 each. Can post.

IMG_9065_zps19a3bb4a.jpg

Door cards- no switches included $20 each. Pick up only

Very good condition except one small blemish as shown in photo.

IMG_9853_zps6d440a34.jpg

IMG_9857_zps86117490.jpg

IMG_9855_zps96138922.jpg

Rear 4 door window switches $20 each (or $40 for all three, driver's switch sold). Can post.

IMG_9858_zpsc03737f7.jpg

A pillar trims $20 pair. Pick up only.

Doors $20 each. Pick up only.

Rear bar, suit respray $20. Pick up only.

IMG_9987_zps800187ad.jpg

Door lock kit - doors, ignition, boot with key $50. Can post.

Steering rack $20. Pick up only.

IMG_9063_zpsacce18d7.jpg

Indicator and wiper stalks $10 each. Can post.

Steering column $20. Pick up only.

Kick panels $10 each. Can post.

Dash plastic surround (pick up only) $20

IMG_9080_zps2a446fc7.jpg

Dash pad $20 pick up only

IMG_9084_zps43191f0f.jpg

Sun visors $10 each. Can post.

IMG_9010_zps3ebb5d79.jpg

Front guard mudflaps $10 pair. Can post.

IMG_9005_zps766b5988.jpg

Sold/unavailable:

Motor and gearbox, headlights, airbox, clutch master, bonnet, passenger guard, under stereo pocket, engine fan, speedo cluster, lower control arms, factory stereo, centre console, stock suspension, castor rods, cat temp sensor, inner guard liners, fog lights, climate control, shifter surround, front bar and grille, AFM, ECU, drivers window switch, side mirrors, stock rims, diff, rear brakes, radiator, interior wiring loom, steering column plastics, handbrake, stock intercooler and piping, rear vision mirror, interior lights, front hubs.

How much for the plastic steering column surround thingy, pending it has no holes or blemishes? Posted to 2444 Port Macquarie?

Let me know :)

pm sent :)

is the front fender the same as for a coupe or are they different? sorry if noob question.

pretty sure they are the same

much chance you'd have a stock or a not too loud exhaust catback for a r33 sedan? also if anyone knows if the front end (guards, front bar, bonnet headlights) are the same between sedan and coupe??

much chance you'd have a stock or a not too loud exhaust catback for a r33 sedan? also if anyone knows if the front end (guards, front bar, bonnet headlights) are the same between sedan and coupe??

nah exhaust sold already, not 100% sure on the front end parts but I only have the driver's guard anyway.

Wouldn't happen to have a speedo drive for RB25 gearbox mate?

i may have one on a stag front cut i have, need to check for ya to make sure it's in good nick

pm me if you want it and i'll check it out

  • Like 1

Hey Mate you dont have the space saver spare wheel by any chance?

Also interested in the radiator support/ boot latch with the horns attached

nah no spacesaver, bonnet latch/rad support is still available

pm me for bank details

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...