Jump to content
SAU Community

Recommended Posts

I have for sale in Melbourne (inner East) a very clean example of an R32 GTST, 1993 model. This car is sensibly modified, still 100% legal (I believe), drives really well and very straight, the doors line up perfectly, no history or sign of accident damage or rust.

I purchased the car late last year for enjoyable drives, but circumstances have changed and it has to make way for something more family oriented. When I purchased it, I was told that the following maintenance/mods had been done:

  • New head gasket kit, valve springs, head polished, new timing belt kit, everything was cleaned inside the block and head.
  • Brand new brake pads and rotors were just installed.
  • Custom built turbo came out of an r34 and was rebuilt using ceramic washers, it’s a bit bigger than a stock r32 turbo so it comes on a bit later.
  • Blitz FMIC with full proper piping.
  • GGreddy dual solenoid boost controller
  • Greddy dual stage turbo timer
  • Upgraded fuel pump
  • A lot of bushes were replaced including steering tie end rods
  • GT-R Aluminium Hood
  • Cusco bars front and back

Since then I’ve continued to improve it to become a really nice, all round machine. Changes / additions have been:

  • Added a 3” Fujitsubo exhaust with a stainless steel rear muffler – great sound but still legal (although still have the std system as well).
  • AVS model 17 inch wheels, 8” at rear, 7” at front which fill out the guards perfectly.
  • Brand new Bilsteins all round with King springs, all to Sydneykid group buy specs. Professionally installed and set-up to just the right height for maximum handling – absolutely fantastic ride/handling result.
  • Brand new Whiteline front & rear anti-roll bars to suit this set-up, but not currently installed.
  • Brand new Splitfire coil packs
  • Brand new oxygen sensor, AFM, K&N filter (in std airbox), auxiliary air control valve, NGK iridium spark plugs.
  • Good second hand rear subframe installed.
  • New JVC double din head unit – all the functionality and great sound, even over the pathetic speakers current in the car.

Other stuff that comes with the car includes a Nismo 260 kph cluster, spare boot lids, one with std GTST spoiler, std springs and shocks, very stiff coilovers for rear, GTR side skirts, a broken GTR style fibreglass front bar.

As per the photos, the car looks great. The interior is also good with no tears or problems other than some dash bubbles. The paint job shows its age close up but is still very passable except for the front bar & the boot lid where the spoiler used to bolt on.

The car runs really well except that I have still not been able to get the idle quite perfect. It varies a bit between 800 and 1100 revs depending on its mood. Seems perfect as soon as you move off idle, is quite responsive at a bit over 2,000 revs, more so in the 3,000 rev range and then fantastic from around 4,000 revs.

Someone tried to steal it recently, so I’ve had to replace the ignition lock. All now fine but I haven’t had time to get the keys matched up, so now there is one key for the doors and a separate one for ignition.

Car is registered in Victoria until March 2014. Selling without RWC as I have time difficulties at the moment, but believe there are no significant rwc issues. Would like to get $7,500 for it but will listen to reasonable offers. Call me anytime on 0414 892 222.

post-105089-0-47289100-1376877229_thumb.jpg

post-105089-0-64059100-1376877246_thumb.jpg

post-105089-0-65392800-1376877262_thumb.jpg

post-105089-0-06906100-1376877276_thumb.jpg

post-105089-0-71647600-1376877291_thumb.jpg

post-105089-0-06281600-1376877305_thumb.jpg

post-105089-0-83924100-1376877321_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/430487-1993-r32-gtst-for-sale-melbourne/
Share on other sites

Obviously mucked up photos first time, so here they are (hopefully) - nope, they worked fine with firefox, just not with explorer.

Edited by Al-r32fan

Would happily load larger ones but everytime I try to add a photo it gets reduced from around 500Kb to around 135Kb. I'm stuck unless someone can advise what I'm doing wrong. Otherwise, happy to send them direct via normal email. My email address is [email protected].

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...