Jump to content
SAU Community

Mugabetown - Whoretownin' At It's Worst.


Recommended Posts

Qlders must be much more relaxed. Down here you go out with fully hectic sik aspiring amateur want to be race car drivers that chop you on corners, spray debris all over your car, because they can't stay on the black stuff; over rev and drop oil and conrod/block pieces all over the track or run into the back of your car b/c apparently friendly track day means full boost up your arse and then realise the merits of a brake upgrade after the fact. That's it I am moving lol

Didn't make it to happy laps this morning... too many schnapps at the german club last night :P

What's wrong with this picture? #@Sick_R31

20140621_155006.jpg

You should have been installing S13 hubs so you have a car to load onto a trailer? And also what Andy circled

Qlders must be much more relaxed. Down here you go out with fully hectic sik aspiring amateur want to be race car drivers that chop you on corners, spray debris all over your car, because they can't stay on the black stuff; over rev and drop oil and conrod/block pieces all over the track or run into the back of your car b/c apparently friendly track day means full boost up your arse and then realise the merits of a brake upgrade after the fact. That's it I am moving lol

Happy laps are just fast paced cruise laps, idiots like that get kicked off pretty quick.

Qlders must be much more relaxed. Down here you go out with fully hectic sik aspiring amateur want to be race car drivers that chop you on corners, spray debris all over your car, because they can't stay on the black stuff; over rev and drop oil and conrod/block pieces all over the track or run into the back of your car b/c apparently friendly track day means full boost up your arse and then realise the merits of a brake upgrade after the fact. That's it I am moving lol

well that doesn't sound very appealing mate.

Sadly, there will always be the gung-ho fully sick yobos

Although I think we (as a club) would filter them out rather quickly as no one wants that

Yeah dooooooo eeeeeettt

Move to QLD - the best state :P

Was good to watch today

Found out a way to inflate my tyer today after nick pointed out it was super low

Was at 14psi

Had to use a bike pump hose, rubber hose, cable tie, air blower and a pressuer regulator. Got it over inflated then dropped it down to what I need with the pressuer Guage.

Have got valve extenders on the way now

Found out a way to inflate my tyer today after nick pointed out it was super low

Was at 14psi

Are you a woman? Crash your car, need people to tell you your tyres are low :P

Didn't make it to happy laps this morning... too many schnapps at the german club last night :P

I am envious of your German Club outing... :cheers: we need one ASAP!

  • Like 1

Was good to watch today

Found out a way to inflate my tyer today after nick pointed out it was super low

Was at 14psi

Had to use a bike pump hose, rubber hose, cable tie, air blower and a pressuer regulator. Got it over inflated then dropped it down to what I need with the pressuer Guage.

Have got valve extenders on the way now

Couldn't you have just driven it to a service station?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...