Jump to content
SAU Community

Recommended Posts

im just used to my new BC coilovers in the R34 which are 6/8 roughly and its firm enough. interesting, might have to do more research into which BC coils to put in the C34....without hyjacking your thread, sorry bud.

im just used to my new BC coilovers in the R34 which are 6/8 roughly and its firm enough. interesting, might have to do more research into which BC coils to put in the C34....without hyjacking your thread, sorry bud.

haha go for it mate, i have no clue what you guys are talking about so some tein coil-over part numbers that would be ok to use would be nice :P lol

Can't speak for BCs in a C34, but I just got a set of HSDs for mine: spring rates differed significantly (mine are harder by about 10%) to the BC off the shelf offering, and I love it: might be a little firm for a daily driver, but dare I say better handling and more comfortable than the "Sydneykid" setup I was running before...

  • 1 month later...

Just an update, cars all arrived and registered, should have updated this alot earlier. Absolutely loving the car! No problems as of yet, need to find a nice set of coil overs for her pretty soon as she needs alot more low! just re installed the HID lights due to compliance and hopefully get around to ordering my custom number plates within the next couple weeks.

1375673_10151953768447697_458723719_n_zp

1381624_10151957424302697_1262124017_n_z

  • 1 month later...

went away this weekend and got a decent picture off the car, pity i didnt have my good camera on me and only had my phone.

Also im about to buy some new wheels and tyres, i test fitted a 18 inch wheel with a lower profile tyre and the speedo was out by about 10kmh, any way i can fix this ? or is it something ill have to put up with when running a smaller profile tyre ? thanks!

529508_10152054367677697_1288590281_n_zp

  • 1 month later...

I was like yes, yes, yes, hmmmm ok...... NO!

Stickers.... :(

At least they are removable.

Yea im still not sure if i will keep all the stickers. Wouldn't mind just one decent looking and sized sticker along the back window but thats still something i have to find. Just can't wait till i get my new wheels!

Such a beautiful car and well looked after. So I see you haven't put the roof wrap on as yet. Whats happening with that. Im thinking of a black roof wrap. Just deciding on gloss or matt

About the roof wrap, Ive been on holidays so once i saved my pennies for the coilovers the rest went on spending money while i was away haha. So hopefully the roof wrap is only a couple weeks away! Its still happening, Dont have to worry about that :P

Out of curiosity what profile size tyres you have on it?

Cant remember of the top of my head, Ill have a look for you when i get home tomorrow :)

Quick photoshop of the wheels i have put on pre order over at WORK Japan, and also the sticker bomb roof wrap ill hopefully be picking up this weekend.

Work D9R

19x8.5 +30 front and 19x10.5 +23 Rear

BDL_47221_zpseafa1247.jpg

Work D9R

19x8.5 +30 front and 19x10.5 +23 Rear

I hope the rears fit too. Might get away with it due to flares and coilovers but for reference, here is how 19x9.5 + 30 sits on an RX (they are +40 with a 10mm spacer).

If 10.5 + 23 were there, it would stick out an extra 20mm roughly

IMAG03241_zpsb634f9aa.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Keeping in mind that I am currently getting flat 10 L/100km on my RB25DET, which means >>500km/tank. I would test this car for vacuum leaks, check codes and AFM signal with NissDataScan as D says, check plugs, do a compression check while they are out.
    • It is hard to be specific half way across the world...but it *seems* like it might have a minor issue. Is the idle stable and does it rev smoothly? I would not expect any pops out of what I am assuming is a standard ECU, standard tune, standard exhaust. You can use Nissan Data Scan to find out exactly what is happening when it runs, the cable/software is reasonably affordable if you are not planning on changing the ECU (which hopefully you are not with an NA skyline) BTW your mileage may not be that far off, these are heavy old tech cars, and being NA might mean you use a heavy foot to keep up with traffic....
    • Hey guys! Y'all are the masters so figured I'd check in on a few items here. - My engine sounds ever-so-slightly more raspy than the other NA RB25s I've listened to. It's barely noticeable but definitely a slightly different sound. - When I back off the throttle at high RPM, I will sometimes get a pop out of the exhaust, assuming this can be diagnosed as misfire. Some history on the car: - Had an exhaust leak in auction sheet but was claimed to be fixed by seller (bought from USA importer).  - Car's coil packs and sparks were replaced when it was sold to me, but unsure on what the gap is and whether the coil packs are correct.  - A prior mechanic had misdiagnosed a pilot or throwout bearing sound as LSPI/detonation. Had played with timing a bit, pops/raspy sound of engine just got worse. Got timing reset. - Had failed emissions a few times. First time went in as is, failed. Second time, replaced cat, still failed, running rich as hell. Third time replaced o2 sensor, passed. Car still smells gassy though. - Timing belt and valve cover gasket also replaced.  - Gas mileage is... low. about 350-400K per tank.  Any idea if I'm having any serious issues here or does this all sound like normal old NA RB stuff and I'm fine to drive it with the pops/slightly raspy engine? If it'll help, I can get drop a video of the sound of the engine.
    • So....to find any R chassis part number, get your VIN (will be something like ER33-xxxxxx for you) and go to: https://www.amayama.com/en/genuine-catalogs/nissan and enter it. From there you have access to a web version of Nissan's part system, FAST. It is a bit tricky to get used to, so maybe have a shot and post up what you think.  You can also search by general model but note in some cases your car might have different options so VIN is safest.  On diagram 211 I got 14075-75T16 for Connector, Water Hose If I search for part 14053‑21U10 that you posted, that is also a water hose but not the one bolted to the plenum and 14075‑04U00 is the fitting where the water hose goes into the block.
    • Yeah now we are talking I much prefer coolers in the front middle because it lessens the chance of a small bump to a corner stopping the whole event. I was thinking the AT cooler can move out of the radiator, delete the AT/engine coolant interwarmer and mount a separate cooler with a thermoswitch somewhere further back as is common in racing, that would be one thing. Beyond that, the engine oil cooler is an obvious one to move to the wheel arch, potentially one on each side, but unused space is an issue. I did have a earlier pic with the bumper off but it doesn't show how busy the corners are: DS is full of the auto driving sensors and PS is totally fully of windscreen washer fluid reservoir But ultimately I was hoping to keep the AC, and the water/air heat exchanger is fundamental so it is not just the radiator that needs to be in front BTW here's airflow to the rad as it ran at the track (one horn is gone now and I'll remove the lights next time):
×
×
  • Create New...