Jump to content
SAU Community

Recommended Posts

Hi Everyone,

Travelling interstate shortly and will be driving a car back to Sydney, seeking guidance what to use to protect the paint on the front bumper - etc.

I remembered seeing a classic photo of a midnight purple R34 GTR with the front end wrapped in blue tape.

For anyone with this experience, what tape do you use? Is it just a standard 3M painters tape?


Was looking at cloth tape but not too keen in applying this because although its quite thick - it is also quite sticky. Obviously dont want to damage the paint upon removal.

Any advice or info would be appreciated.

Cheers.

post-86021-0-32450100-1378272073_thumb.jpg post-86021-0-89432500-1378272080_thumb.jpg post-86021-0-24261000-1378272088_thumb.jpg

You can buy this stuff from super cheap or autobarn it's a black spray that you can peel off after use..

It's to protect your car from stone chips.. Not sure how good it is though..

Not sure on correct name either, saw it in a performance imports magazine not too long ago.

Edited by Zrobe

Wouldn't recommend painters tape.

Ive used it for detailing to mask off seals, trims and gaps and you'll only get about ~ 4 hours out of it before the "glue" starts leaving residue on the paint. And that's when the car is sitting.

I'd go with a hood bra or vinyl wrap.... but prepare the surface properly before you put it on -- > e.g. get rid of any contaminants sitting on the paint.

Guess what Chris?

If permission is granted...

A very irregular SAUer owns a car bra that was tailor-made for his R34 GTR V-Spec.

Interested? He has cancer, so I don't know how accessible he is either.

Mid Blue Mtns

Peelable spray is called plastidip, from autobahn.

I also have a plastic wrap called street wrap. Works well and easy to remove. Can be tricky to apply, sorta like glad wrap lol.

Plastidip would be your best bet. Easy to put on, easy to get off and provides pretty much the same protection as a wrap.

It's $30 a can from Autobarn. To do say half way down your bonnet forward you'll need at least two cans, possibly three. You need to do a few coats.

3m and most vinyl wrap manufacturers do a clear stone protection wrap for this very purpose. I came across it in my search for ricer carbon fibre wrap (yeh I know :closedeyes: ) . It's meant to be removable, but being clear, you could probably leave it in place.

I work at SCA. I'm not sure of what the name of the stuff is but the first comment would be best option. It's an Armor All product that you spray on the front end of your bumper and it protects from scratches and chips. Costs about $24.95 a can (I think). Simply spray on and peel off when you're done. I believe there is clear, white or black

Hey guys,

Ended up driving back unprotected, just kept reasonable distance from any cars / trucks that could throw gravel - etc up.

My partner intends on painting the front bar anyway she wants it to be perfect, however upon inspection at home - there were no stone chips or visible wear and tear as a result of the drive back.

Cheers.

For future search sake, I have used this:

http://www.autoskin.com.au/

Works pretty good for dust/general road typr spray. Obviously if someone throws a decent sized rock up it always has potential to go through.

  • 2 months later...

That's pretty lucky, the two best choices would be to plastidip your bumper and behind wheels. Or go to bunnings and get edge lock masking tape (the one that leaves no residue).

Plastidip is easier to apply and remove. Both are going to cost you the same

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...