Jump to content
SAU Community

Recommended Posts

Hi guys first post for me,im new to gtr's.I have just recently bought a r33 gtr from Adam at JEM.It currently makes 343kws at the wheels on 20psi.

My plan is to switch it over to United e85 with an end goal of 400kws at the wheels.IT has a precision 6266 turbo and other supporting mods.At the moment it has an 044 intank,i was thinking of replacing this with a walbro e85 450l/ph pump and replacing 750cc injectors with some bosch id1000s.

I have asked Adam at jem and he said in theory this pump should do the job,but has not personally done it.

Your thoughts guys or experiences would be great.I will directly wired this off the battery thru a relay to get good volts to the pump.I have used the search function,but could not find an answer.

From the last page of the RB26 dyno results thread:

forged bottom end

stock cams and valve springs

metal head gasket with ARP head studs

precision 6266 0.84 T4 divided rear

3.5" dump/cat back

GFB EX50 50mm external gate

1200cc injectors with walbro e85 pump

power fc d-jetro

409rwkw @ 26psi on Caltex eflex E70, at the limit of stock cams and injectors

At 13.5v and 40 psi rail pressure it advertises 430l/ph and on 12v at 40 psi it flows 375l/ph.I plan on running a direct feed to get near 13.5 volts.So at 40psi pressure should outflow 2x 044s.I was toying with the idea of the bosch id2200cc injs.Thanks guys

Not sure on that one piggaz,i think I will go straight with the bosch id 2200cc or similar brand.Car has haltech platinum pro plug-in,should handle the big injectors ok.Thanks guys.

Have a gander at my attachment.

I wrote a pretty simple spreadsheet for calculating and comparing different fuel systems for my car. Obviously it's to suit my setup but could be easily tweaked.

I have highlighted all of the cells you need to update then see sheet 2 and graph's it all out.

IE set the highlighted cell to your desired base fuel pressure. write out your hp and boost based off a close dyno sheet. in my case when it was tuned for bp98. and then fill in the injector flows and corresponding pressures.

with this info it tells me that my injectors are too small for me to convert over to E85 and keep my same HP. unless I either run a 70PSI base pressure or go about an 80% duty.

fuel calcs.zip

thanks ss8 gohan,will go with the e85 450l/ph pump.Still tossing up on the injectors.Tuner thinks 1000cc ids will do,but a lot of guys on here think the 2000cc are the go.Most suppliers will warrant the 1000cc with e85 but not the 2000cc,Will do some more research.Thanks all,for ideas and tips.

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...