Jump to content
SAU Community

Recommended Posts

Hi there i'm chasing some oem parts for my skyline project.

Location SYDNEY NSW

Looking for the following;

RB20DET throttle body

RB20/25/26/30 flywheel

RB20DET starter motor

32 GTS-t indicators pair

32 GTS-t wiper motor

RB20/S1 RB25 AFM

RB20DET engine mount brackets (don't need the engine mounts)

RB20DET air box

If you have any of the following please throw me a PM with a picture, price and location!

Thanks

Willis

Edited by Willis
Link to comment
https://www.sau.com.au/forums/topic/432588-sydney-wtb-r32-gts-t-parts/
Share on other sites

I have every single part that you need, in Brisbane so will work out a package deal including postage and let you know

Cheers

PM sent, thanks mate!

RB20DET throttle body


RB20/25/26/30 flywheel


RB20DET starter motor


32 GTS-t indicators pair


32 GTS-t wiper motor


RB20/S1 RB25 AFM


RB20DET engine mount brackets (don't need the engine mounts)


RB20DET air box

  • 3 weeks later...
  • 2 weeks later...

RB20DET throttle body


RB20/25/26/30 flywheel


RB20DET starter motor


32 GTS-t indicators pair


32 GTS-t wiper motor


RB20/S1 RB25 AFM


RB20DET engine mount brackets (don't need the engine mounts)



I need a cheap front mount intercooler setup for a 32. Prefer quality core! Will also buy just a core!


I need an exhaust to suit a 4 door, a 2 door exhaust will work. Interested in a titanium catback also <3


Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...