Jump to content
SAU Community

Recommended Posts

Hey guys just pulling down my rb30 for reco. Got to my crank gear the cog that the timing belt runs on don't know what it's called. I can't get it off. I've put pry bars behind it to try n leaver it off smashed behind it with a flat head to pry it off and it's just not moving.

Any help would be good thanks. It's so frustrating

Cheers Cuong.

Link to comment
https://www.sau.com.au/forums/topic/433124-cant-remove-my-crank-gear/
Share on other sites

Remove the flywheel seal retainer, main stud cradle, and all the bolts on the pump. Then lift the crank and pump out together.

Once the crank is out of the block, you can get a claw puller behind the gear and take it off the crank without destroying it. Take it to an engine workshop and have them do it if you don't have a claw puller.

The other option is drill through the gear in multiple places down to the woodruff key, and then break the gear with a cole chisel. I prefer the non-destructive method, saves you buying a new gear that way too.

Also, the reason they are jammed tight is always because they have started to come off crooked and then jammed.

Have a look at which way it is not straight and bash that side back straight, then try again.

I've tried to get it off straight but it just doesn't move.

I'd prefer to just pull the gear off. Don't wanna pull the crank out yet I need my friend with before I can do that, he is over watching my build and help me through.

Check the woodruff key is not burred, i saw a workshop near me trying to pull one off a 2JZ and the moment i ran my fingers over the key you could feel the sharp edges, a bit of a file and it came off smoothly.

If its stuck on before it even moves a little, try the removing the crank method as its the least destructive.

In the past ive managed to move them by hammering a knife gently down each side around the back where the rear guide washer is to get them moving with some wd40 spray added to the mix, once they move a little, some lube and some working and a bit of gentle tapping gets them off.

Just a tip for when you put it back on, get a tube of anti seize and smear it on the crank nose and inside the gear. It's a moly based greese that doesn't dry up.

Makes life a lot easier next time!

I got a flat head screw driver and got it in between the oil pump and the gear and just slowly twisted the screw driver until I saw the gear budge and then did it on the other side. Kept doing this until there was enough space for the pulley puller claws to fit. Came right off without any dramas :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I used to have Walbro 255's when they were a pretty common update. (or were they 044? 040?) In any case I had a dirty tank. I thought the tank was good, but I would find the filter would clog in maybe ~50km of driving. If the issue persists, well, your fuel system or tank has crap in it that the pump is sucking up.
    • Hi. Ok thanks for the info. I/we do not know what tune is on that Nistune ECU so it is why there is stock ECU and that Nistune is for later when the car is done. I have guy who tunes Nistune and other ECU so i will then take it to him to see and properly tune for the car   And for the update. On 99,9% it is bad fuel pump. Which is wierd cuz it is like 2 years old(brand new walbro 255) and that filter (also brand new) was dirty.  I was alwaya pumped premium(100) on very good petrol station so i dont know how is that possible...  
    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
×
×
  • Create New...