Jump to content
SAU Community

Recommended Posts

Fair nuff, though for future reference or anyone else's benefit, the turbo and exhaust manifold can all be removed with simple hand tools. You'll need a few sizes of socket wrenches for the tight spots, and a selection of spanners. Other than that you may need to get a thread repair guy out, as I did when a stud broke (or probably was already broken). Good time to replace all the studs and gaskets.

As a matter of fact I think I only had to get underneath the car to get at 3 bolts. Hear that M35 guys? Its soooooo hard on an RB......

Fair nuff, though for future reference or anyone else's benefit, the turbo and exhaust manifold can all be removed with simple hand tools. You'll need a few sizes of socket wrenches for the tight spots, and a selection of spanners. Other than that you may need to get a thread repair guy out, as I did when a stud broke (or probably was already broken). Good time to replace all the studs and gaskets.

 

As a matter of fact I think I only had to get underneath the car to get at 3 bolts. Hear that M35 guys? Its soooooo hard on an RB......

The biggest thing that scared me away from the repair was how to do the welch plug(s) themselves as it's not something I've ever done and no-one I know has done.

I looked over what it was to get the manifold off and it didn't seem like it would have been a major issue.

Just sold a car too so I'm cashed up now to get the Stag done quickly and professionally as it is my daily driver.

Welchies are not that bad to do. The key to successful repairs on anything is prep work AND cleanliness! Using a sealant like Permatex aviation No.3 is also ideal, especially on an older block.

  • 3 weeks later...

So here's an update on my stagea.

Mechanics have done a bunch of work

- replaced 4 welch plugs on that side of the block

- replace crank seals

- replace cam seals

- replace timing belt

- replace thermostat

- replace water pump

- replaced inner cv boots

- replaced turbo (stock v45 i supplied as the old one had a terrible whine)

- fit supplied aftermarket oil filter re-location kit (inner feed tube thing was too big to fit in the block apparently :()

- flush water

- replace oil & filter

Picker her up last friday arvo and got it home late that night. Did some driving around on Saturday morning all good.

When for a trip down to the gold coast and had it overheat quite bad once and not so bad three other times afterwards... only on the highway @ ~110km/h under load and not in peak hour traffic.

Saw the mechanics again this morning and they've basically confirmed my fears the original factory radiator is either blocked/getting blocked. They flushed it once after doing the welch plugs and when I got them to have a quick look today the water under the cap is starting get very brown again.

Couldn't see an obvious leak/crack or excess pressure build-up so we're only assuming this is the problem so far.

Can anyone recommend some replacement radiators that I should look at?

The mechanic suggested not anything much more than 45mm thick as this could restrict the airflow too much.

I'm thinking that I can get one off the net an replace it my self and flush the system a couple of times.

Any thoughts are appreciated, if you've read this far :P

Most of the buckchoy alloy 42mm ones will do an acceptable job.

SAU NSW members get a discount on Fenix radiators and the one I installed in the S2 Stagea works perfectly and fitted with minor shroud trimming. The radiator in the GTS-t fitted without any trimming.

  • Like 1

Most of the buckchoy alloy 42mm ones will do an acceptable job.

SAU NSW members get a discount on Fenix radiators and the one I installed in the S2 Stagea works perfectly and fitted with minor shroud trimming. The radiator in the GTS-t fitted without any trimming.

Edit: i'm in QLD and not an SAU paid member

Had a quick ebay browse last night and i can see 'mishimoto', 'koyo' and some other ones that allegedly fit the WGNC34.

Thinking I might just buy one of these and fit it myself.

Another interesting thing to note; if I brake really suddenly the engine stalls... mechanic mentioned it might be the AFM recognises the lack of airflow and the ECU thinks the ignition has been switched off...

Edited by wookster

One thing that you need to remember is that the oil cooler for the transmission also runs through the radiator, and most alloy radiators don't have this built in. It is simple to put an external cooler for the trans but sucks when you forget and have to order a taxi to get you to the spare parts shop!!!!!!

Edit: i'm in QLD and not an SAU paid memberHad a quick ebay browse last night and i can see 'mishimoto', 'koyo' and some other ones that allegedly fit the WGNC34. Thinking I might just buy one of these and fit it myself.Another interesting thing to note; if I brake really suddenly the engine stalls... mechanic mentioned it might be the AFM recognises the lack of airflow and the ECU thinks the ignition has been switched off...

time for a new mechanic :) The ecu doesn't have to wonder if the ignition is on or not, is connected to the ignition.

One thing that you need to remember is that the oil cooler for the transmission also runs through the radiator, and most alloy radiators don't have this built in. It is simple to put an external cooler for the trans but sucks when you forget and have to order a taxi to get you to the spare parts shop!!!!!!

Hahahah oh dear that story sounds terrible.

Sorry mate, it's a manual (factory RS-FOUR-S) so I believe there is no tranny cooling you mention.

time for a new mechanic :) The ecu doesn't have to wonder if the ignition is on or not, is connected to the ignition.

Hmmmm... so is it possible that if enough air isn't flowing could this ruin mixture and maybe flood the engine?

Braking hard and it stalling on me makes me very confused...

Edit: i'm in QLD and not an SAU paid member Had a quick ebay browse last night and i can see 'mishimoto', 'koyo' and some other ones that allegedly fit the WGNC34. Thinking I might just buy one of these and fit it myself. Another interesting thing to note; if I brake really suddenly the engine stalls... mechanic mentioned it might be the AFM recognises the lack of airflow and the ECU thinks the ignition has been switched off...

I realise you are not a NSW member but the alloy radiators are more or less the same design so they will fit regardless of where you buy it from.

Another interesting thing to note; if I brake really suddenly the engine stalls... mechanic mentioned it might be the AFM recognises the lack of airflow and the ECU thinks the ignition has been switched off...

Is your brake booster leaking?

Is your brake booster leaking?

+1

We're going to need alittle more info.....

Has the brake booster hose been off? There is a one way valve in the hose.

What condition is the air filter in?

What is the idle like?

Does it run abit rich?

 

+1

 

We're going to need alittle more info.....

 

Has the brake booster hose been off? There is a one way valve in the hose.

Not by me, the mechanic might have...

What condition is the air filter in?

Pretty good. Previous owner had a oilable one in the factory airbox which I keep reasonably clean, though I havent cleaned and re-oiled in about 6 months, maybe ~6000kms.

What is the idle like?

Idle seems fine, ~650 rpm when up to running temp

Does it run abit rich?

The AFR guage (aftermarket - previous owner) on the dash indicates not lean or rich at cruising speeds. Not sure on a good way to guage richness off the top of my head?

Thanks, I've heard some people like em. PWR was recommended as the top notch ones from the mechanic (~$900!)

Koyo is the OEM; very high quality product. Priced accordingly.

More than one person on this forum would disagree with the opinion of your mechanic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...