Jump to content
SAU Community

Recommended Posts

My rb25 is blowing a fair amount of blue smoke under hard acceleration. I did a compression test and it came up 160 across all 6. There is no smoke on idle or slight revving only when I give it a good rev. I replaced the turbo with a brand new one and the return doesn't seem clogged or anything. Has all brand new feed and returns. Also I don't have a down pipe on it at the moment and it doesn't make full boost until about 5500 or so on a t04e. The blow off valve doesn't go off and there is no sound of releasing pressure when off the throttle. All cooler pipes are tight. What would be the cause of excessive blue smoke?

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/
Share on other sites

it has a brand new turbo on it with 1.2mm restricter, what are the signs of bad valve stems? ill give it a boot full and it will blow a shitload of blue smoke on hard acceleration, but if i keep boosting it the smoke gradually gets less and less, so pretty much the more i flog it the less it smokes so to speak (no i dont flog it all the time lol)

which leads me to believe its valves as theres no time for vacuum to draw oil through the seals.... but theres no smoke on start up or just putting around under say 3.5k rpm

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/#findComment-7101937
Share on other sites

I have had to install two 0.9mm restrictors to some Garretts just to stop the oil pumping out of the seals, you can tell as the oil is unburnt in the dump. If it is burning it, it is most likely internal, but check the intake for oil first, it could be the compressor seal or just leftover oil from the last turbo failure...

T04e is a pretty big turbo, I hope you haven't done the ring lands from booting it without tuning first. It will also be more responsive once it's tuned properly.

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/#findComment-7102089
Share on other sites

As stated above, potentially the oil control rings. Possibly also valve stem seals - will a leakdown test return poor figures if valve stem seals are shot? Or would they not allow enough air past?

Your other symptoms like the BOV are almost certainly unrelated :)

I'd start at the beginning of the system (filter and intake pipe - rocker breather return) and work your way to the exhaust. You've ruled turbo seals out (well, you haven't - but would be f**king horrible bad luck if you had 2 buggered turbos :P), so that leaves you with the rocker cover breather return, valve stem seals, and oil control rings to point at.

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/#findComment-7102998
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
    • EMU Classic. For what I need it to do I see no reason to upgrade. Link and Haltech would both cost an extra chunk of money for a lot of unutilized features
×
×
  • Create New...