Jump to content
SAU Community

Recommended Posts

My rb25 is blowing a fair amount of blue smoke under hard acceleration. I did a compression test and it came up 160 across all 6. There is no smoke on idle or slight revving only when I give it a good rev. I replaced the turbo with a brand new one and the return doesn't seem clogged or anything. Has all brand new feed and returns. Also I don't have a down pipe on it at the moment and it doesn't make full boost until about 5500 or so on a t04e. The blow off valve doesn't go off and there is no sound of releasing pressure when off the throttle. All cooler pipes are tight. What would be the cause of excessive blue smoke?

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/
Share on other sites

it has a brand new turbo on it with 1.2mm restricter, what are the signs of bad valve stems? ill give it a boot full and it will blow a shitload of blue smoke on hard acceleration, but if i keep boosting it the smoke gradually gets less and less, so pretty much the more i flog it the less it smokes so to speak (no i dont flog it all the time lol)

which leads me to believe its valves as theres no time for vacuum to draw oil through the seals.... but theres no smoke on start up or just putting around under say 3.5k rpm

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/#findComment-7101937
Share on other sites

I have had to install two 0.9mm restrictors to some Garretts just to stop the oil pumping out of the seals, you can tell as the oil is unburnt in the dump. If it is burning it, it is most likely internal, but check the intake for oil first, it could be the compressor seal or just leftover oil from the last turbo failure...

T04e is a pretty big turbo, I hope you haven't done the ring lands from booting it without tuning first. It will also be more responsive once it's tuned properly.

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/#findComment-7102089
Share on other sites

As stated above, potentially the oil control rings. Possibly also valve stem seals - will a leakdown test return poor figures if valve stem seals are shot? Or would they not allow enough air past?

Your other symptoms like the BOV are almost certainly unrelated :)

I'd start at the beginning of the system (filter and intake pipe - rocker breather return) and work your way to the exhaust. You've ruled turbo seals out (well, you haven't - but would be f**king horrible bad luck if you had 2 buggered turbos :P), so that leaves you with the rocker cover breather return, valve stem seals, and oil control rings to point at.

Link to comment
https://www.sau.com.au/forums/topic/434537-rb25-blue-smoke/#findComment-7102998
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...