Jump to content
SAU Community

Recommended Posts

Just some left over parts that are not needed. Located in Melbourne. Most items can be posted at an additional cost.


Cusco strut tower bars suit R32 Front and rear. Avg condition. Scratches and paint chips. $180 pair


HKS Boost gauge and GReddy A-pillar pod Up to 2bar. Suits R32 dials perfectly with black back and red needle $160


Sports steering wheels (leather) 1. Momo, good cond, leather not worn through. 2. Unknown Italian brand, carbon inserts. 3. OMP style deep dish blue stitching, hardly used $40 each


Antenna booster - 12V amplified New. Boosts weak FM radio signal (10dB gain). Problem particular to R32's where the antenna is built into the windscreen. $25


CUSCO springs (from Zero 2E coliovers) Cusco ID65 200 series. Spring rate: 11kg, Inner spring diameter: 65mm, Length: 200mm, Stroke: 100mm. Travelled 2000kms $120 pair


A'PEXi ECV (Exhaust Control Valve) and cat Control the loudness of your exhaust. Approx 40% reduction on my 3" exhaust. Catalytic converter is empty / gutted. $90


Child anchor points and brackets Fitted onto rear parcel shelf during compliance process $20


Oil catch can Never used. Looks about the size of 500ml. $35


Blaupunkt CD/MP3 Head unit Excellent condition. Detachable face. Anti-theft features. Comes with loom plug $70


Hks Electronic Torque Split Controller (Hks Etc) And Hks Electronic Drag Adaptor (Hks Eda) $620 pair




Pics available for all items!


Link to comment
https://www.sau.com.au/forums/topic/434937-random-aftermarket-bits-and-pieces/
Share on other sites

A'PEXi ECV (Exhaust Control Valve) and cat Control the loudness of your exhaust. Approx 40% reduction on my 3" exhaust. Catalytic converter is empty / gutted. $90

got a picture?

  On 18/11/2013 at 12:07 AM, GH05T said:

A'PEXi ECV (Exhaust Control Valve) and cat Control the loudness of your exhaust. Approx 40% reduction on my 3" exhaust. Catalytic converter is empty / gutted. $90

got a picture?

post-26500-0-59302600-1384757093_thumb.jpg

post-26500-0-64320200-1384757133_thumb.jpg

  On 18/11/2013 at 6:47 AM, CRZY32 said:

On closer inspection I dont think this was APEXI. Might be Autobarn Driftek branded. Been sitting in storage for a while I cant remember

so it replaces the cat?

  On 18/11/2013 at 11:15 AM, GH05T said:

so it replaces the cat?

This has already been sold. The valve sandwiches between the cat and the pipe behind the cat. I was selling with an empty cat.

Hey mate could you please send me a picture of "HKS Boost gauge and GReddy A-pillar pod Up to 2bar. Suits R32 dials perfectly with black back and red needle $160"

  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...