Jump to content
SAU Community

Recommended Posts

As delusional as Maldanado this bloke.

http://www.planetf1.com/driver/18227/9487921/JEV-I-showed-my-potential

Scrappiest of races with penalities, running off the road left right and centre...yet is claiming it as his arrival drive. Where did he qualify again? :) Hack. Off you go to Nissan LMP1 program and leave Romain to fly the F1 flag

obvious troll is obvious

I'm just going to leave this here:

Last 2 races:

Singapore

12 13 Pastor Maldonado Lotus-Renault 60 +66.9 secs 18

13 8 Romain Grosjean Lotus-Renault 60 +68.0 secs 16

Italy

14 13 Pastor Maldonado Lotus-Renault 52 +1 Lap 16

15 99 Adrian Sutil Sauber-Ferrari 52 +1 Lap 14

16 8 Romain Grosjean Lotus-Renault 52 +1 Lap 17

what's that saying? "you're only as good as your last race", or in this case two lol

Edited by hrd-hr30

hmmm,

a "foreign substance" contaminated the electronic circuits in his steering column...

then a later tweet says

the contaminant was a substance used in normal pre-event servicing of the component.

dodgy. If it was a nomal substance used in normal servicing, why would you call it a foreign substance/contaminant? Funny how this normal substance used in normal pre-event servicing only found it's way into the electronics immediately as the cars rolled out for the race, not at the start of the event.

f**k it, i had to listen to years of Webber conspiracy theorists! :P

hmmm,

then a later tweet says

dodgy. If it was a nomal substance used in normal servicing, why would you call it a foreign substance/contaminant? Funny how this normal substance used in normal pre-event servicing only found it's way into the electronics immediately as the cars rolled out for the race, not at the start of the event.

f**k it, i had to listen to years of Webber conspiracy theorists! :P

What substance would you use to "service" a wiring loom that would potentially contaminate the electronics that the loom plugs in to?

Think hair gel is a more believable explanation.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...