Jump to content
SAU Community

Recommended Posts

Before:- My EVO had a few scratches here and there + particulate matter + swirl marks despite a Grade 4.5 in Osaka

This is how the car appeared before Eugene got to it on a Sat morning.

P1050298_zpsba8cbcd1.jpg

After:- By Sun afternoon after being picked up from Hornsby Station, my car looked like this...

Terry-45_zps8012ad2c.jpg

Terry-44_zpsb04814c6.jpg

Terry-46_zpsdd1038dd.jpg

History:- Eugene has had many wraps before with cars that he's detailed in HPI, Zoom and PG magazines; but personally, he did wonders with a car that was Grade 3.5 > Best Concours at the R34 GT-R 10th Anniversay and Daily Telegraph Cover Story.

Before:- Eugene knew he had a job and a half, to do with this...

R34Aug08010.jpg

After:- And it ended up like this...

God_speed-17.jpg

Eugene is available to anyone in the Sydney area on 0421141538 but it's best to book well ahead.

Thanks Eug.

Link to comment
https://www.sau.com.au/forums/topic/435825-eugene-chans-work/
Share on other sites

Yep, Eugene does/did some work for the dealership that I bought my stagea from.

Needless to say it was very well presented when I bought it, and has made subsequent detailing of the car easier.

+1 for Eugene.

Yes that's him Nick.

One thing I found fascinating about Eugene's attention to detail is the way he goes over all metal panels with his paint thickness gauge to see...

a) if there's been panel repair and

b) how much paint he has to work with.

On the Bayside Blue GT-R, there was a consistent 320 microns.

EugeneDetail14.jpg

On the Pearl Black GT-R, there was a consistent 180 microns.

R34GTR102_zps834ffef2.jpg

On the Mica Grey EVO, there was a consistent 120 microns except for the front left guard which was about 200.

The omission of any repair on the LF on the auction sheet I guess, is something to consider about Grade Validity.

Terry-48_zps14612286.jpg

On the Polar White N1, Eugene only had about 80 microns to play with - *gulp

Polish was devoid of cutting compund.

Eugene-14.jpg

It could have been so easy to cut through the paint...

  • Like 1

Actually, there is far less to play with as a detailer.

The tool measures the whole thickness, where a detailer is essentially working with just the clear coat layer to produce results. The clear coat layer is thin compared to the paint thickness.

I too went over the stagea with a thickness gauge, finding a clean straight car :) The roof and bonnet were however notably thinner than the other body panels.

The goal is to take off the least amount possible. But as far as I know even a fairly aggressive buff will only take off about 10 microns, however, its not something you want to do every 6 months... Sometimes better to leave some swirls behind.

  • 1 month later...
  • 1 month later...
  • 4 months later...
  • 2 weeks later...
  • 5 months later...

Being detailed as we speak. Eugene's final task before Christmas.

A "Before" shot...

but Eugene can show just how dirty this was.

Terry-116_zps24fb10f5.jpg

V-Spec II N1

* Eugene has kept abreast of new processes - a sign of a professional who refuses to stop adding to his wealth of knowledge

* New cleaning agents

* New polishes to match is array of pads

* A choice of post-polish coatings

a) quality sealant and quality wax or...

b) ceramic coating - yes at extra expense. But that's best to discuss with the expert.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...