Jump to content
SAU Community

How To Get Rid Of Sluggish Coldstart/warmup And Bad Fuel Economy On Your Nistuned Rb20Det/z32/gtr Ecu.


Recommended Posts

  • 1 month later...
Who knows then!

Hey rolls quick question about this

Can you make these changes via a trail version of nistune?

I don't want to pay a workshop in ACT to make these small changes because I'm sure they will try charge an arm and a leg and DVS lives too far away for something this small

Pretty sure they don't make a trial version of nistune anymore, you should email pete/matt and say this is the only change you want to make, they might be able to help you out or point you in the direction of someone who can do it for basically free, they are both good blokes so I'm sure they will at least suggest something.

If they do have a trial version, let us all know!

http://www.nistune.com/contact.php

Edited by Rolls

That's a shame that people do that Matt.

As it would take literally 5minutes, perhaps your tuner could make the changes for free or cheap as Manuel Kasko, especially as you are bringing in a bit if knowledge for them to help future customers.

Edited by superben

Spoke to Nistune which I guess is Matt above haha.
Too many dodge people have wrecked it for us.

I'm going to wait for my 34 to pass compliance, then I will pull the ECU out of the 33 and send it to Matt to get sorted.

That's a shame that people do that Matt.

As it would take literally 5minutes, perhaps your tuner could make the changes for free or cheap as Manuel Kasko, especially as you are bringing in a bit if knowledge for them to help future customers.

Tuner is about 4 hours drive from here.

ACT Nistune tuners will probably charge me too much for the changes.

Changes are disabled in the trial now, because some people would tune customers cars using the trial version!

If people are so cheap they won't spend the $200 to get a personal license (even though they should get a tuners license) then I doubt getting rid of the trial version will stop them, they will probably just steal someone elses license code or get 20 people to chip in and do that.

Do you have checks in the software to stop people sharing license keys?

Tuner is about 4 hours drive from here.

ACT Nistune tuners will probably charge me too much for the changes.

Why not give a tuner a call? explain exactly what you want them to do, surely they wont charge you more than $20 for a 5 minute job.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...