Jump to content
SAU Community

Recommended Posts

I was told the vl (rb30) water pump fits the rb25's, but i was just wondering if anyone knew if they fit the rb20det as well??

Also, can anyone give me a quick run down on removal and install of a water pump.

This is how i see it,

*use white out to mark where cas sits on timing cover as i don't have a timing gun

*remove cas

*remove timing cover

*mark appropriate spots with white out so timing belt goes straight back in original position

*remove water pump after draining coolant system

*clean around the area with a rag etc and apply gasket with some gasket goo (any suggestions? )

*install new water pump

*put timing belt back on inline with white marks

*put all covers back on

Any suggestions/tips etc would be great.

cheers

Jayson

Link to comment
https://www.sau.com.au/forums/topic/43687-water-pump-queries/
Share on other sites

I reworded my search and got a few more results. So far i have removed mostly everything except for the harmonic balancer. I've cracked the centre nut but now need a harmonic puller to remove it. I paid $74.50 for a rb30 water pump (Protech) and had some gasket goo around so all up it should hopefully only cost me $74.50.

Joel the rb30 water pump seems identical to me. The only difference being that the top 10mm bolt hole is not slotted like the nissan one.

Cheers

Jayson

There is a "powermax" one for like $80 from some parts places I've noticed (supercheap, etc).. Fit sheet says RB26DETT, RB25DET, RB30E, and RB25DE so if you ask me that sounds universal :P

They missed RB20DE and RB20DET and RB30ET. :slap:

  • 2 weeks later...
So it is confirmed the rb20det motor will use an aussie delivered r31 skyline rb30 water pump....

Yes, definitely, absolutely, not a problem, all RB water pumps are interchangeable, go for it, let 'er rip, whack it on, bolts straight up etc etc.

You need to be aware that while they fit, there are slight differences in performance.

The RB20DE pump flows slightly less water at all RPM's (smallest engine, needs less cooling).

The RB26DETT pump flows slightly less water at high rpm (stops cavitation). :)

The RB26DETT N1 pump actually flows less than the standard pump for sustained high rpm use (racing). :idea:

The RB30E and RB30ET pumps are not designed for sustained high rpm (over 7,000 rpm), they are SOHC remember.

The RB20DET and RB25DET pumps are pretty similar in flow, but the impellers look different. :confused:

I think the RB25DE pump is prety much the same as the RB20DE pump but I haven't had them side by side to compare.

Hope that helps

So what would be the right choice of water pump for a lower rpm 800hp Rb30/26

Standard RB26DETT would be my choice. There is one on my RB31DET, so I guess you could say I have put my money (or faith) where my mouth is. :)

  • 3 months later...

sorry for digin the thread up again but im in the process of upgrading my water pump and have a few questions.

i wanted to upgrade to the N1 but syd kid says there is less flow than standard so does that mean for daily use and the occasional track/drift days its not worth it?

does the stock RB26dett water pump flow better than the stock RB25det??

anyone??

Maybe I am the only one who has compared them, but the spec sheet confirms it. The N1 water pump is specifically designed for continuous high rpm use, so it doesn't cavitate. This means it pumps less water around at lower rpm. So if you use your RB26 a lot (only) on the track, an N1 water pump is maybe worthwhile. But driving around the street it will be a handicap, maybe on hot days with the aircon on, in traffic. The RB30 pump is much better for this as it was designed for lower (average) rpm.

That's all for me :birdie:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...