Jump to content
SAU Community

Recommended Posts

For sale are some quality parts I consider surplus after a few changes in direction....





1. GT2860-7's with 400km's travelled, 2nd hand cam (exh) broke and bent some valves, rebuilt engine to higher hp spec's than the -7's.


In excellent condition, includes garrett actuators.



Price; $1500.




2. Axxis Hero wheels, 19/9.5 at +22 offset, They have almost new(400km) 265/30/19 Kumho Ku31's , the wheel pictured has the worst rash,


The same wheels in my avatar, Selling due to finding some LMGT1's.



Price; $1500.




3. R33 GTR specific Apexi PFC with hand controller.



Price; $650.




4. Ti front pipe, unknown brand, Learnt the hard way R34 pipes are indeed longer than the R32 & 33's


Pics indicate its good condition.



Price; $500.




5. Kakimoto Hyper Fullmega N1 cat back exhaust in good condition, front section heat wrapped.



Price; $350.




6. CES dump's and matching front pipe, includes adaptors for lambda sensors.



Price; $300.




7. Jjr coil pac's, where replaced with Splitfires which didn't change the issue.



Price; $200.




8. Std R33 RB26 injectors.



Price; $200




9. Std R33 RB26 Crank balancer/pulley, has travelled 400km, upgrading to crank trigger set up.



Price; $200.




10. Chinese?? GTR hard pipe kit...silicon joiners and hose clamps included.



Price; $150




11. 3in Hi flow cat in good condition.



Price; $75




12. Have a std size R33 RB26 crank,


Good condition.



Price; $250




Misc...RB26 rod's and pistons, also a sleeved block which is cracked through to the water jackets from the head studs.


Offers considered....




Happy to post at buyers expense, pick up is fine too....



PM me on here or text to 0418630718.



Cheer's Glen.













post-56086-0-99564400-1388816983_thumb.jpg

post-56086-0-64647600-1388817018_thumb.jpg

post-56086-0-83018500-1388817049_thumb.jpg

post-56086-0-60623300-1388817070_thumb.jpg

post-56086-0-92091000-1388817091_thumb.jpg

post-56086-0-35979700-1388817111_thumb.jpg

post-56086-0-55434400-1388817139_thumb.jpg

post-56086-0-59794100-1388817173_thumb.jpg

post-56086-0-01539700-1388817208_thumb.jpg

post-56086-0-68040200-1388817231_thumb.jpg

post-56086-0-72935300-1388817257_thumb.jpg

post-56086-0-63194900-1388817288_thumb.jpg

post-56086-0-04827100-1388817314_thumb.jpg

post-56086-0-28086800-1388817348_thumb.jpg

Pm's replied...

Also have 2 intercooler's, 1 from an R33 GTR and the other from an R34 GTR, relatively good condition, pic's if your interested.

R33 int- $200

R34 int- $250

  • 2 weeks later...

Gday...

The Ti pipe is 70x2 into 80mm, it will fit under the car no problems but is a fraction longer, off the shelf cat back systems will no longer fit without mods...

Hard pipe kit SOLD and dispatched.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...