Jump to content
SAU Community

Recommended Posts

I tried this - water didn't really bubble. A tiny amount of white froth developed as the coolant started to get hot. Not sure if that's meant to happen but I read up that it froths a little when the radiator starts to build up pressure.

Massive head f**k it has become!

that sound about right and my best guess is HG, just enough to upset the cylinder pressures

I have a feeling it's the injector. Are you sure they're brand new? I bought the fiveo 1000cc injectors and they are 2nd hand high flows and one even had surface rust. I wouldn't recommend the high flows really. It can be difficult to cold start my engine now.

that sound about right and my best guess is HG, just enough to upset the cylinder pressures
I might buy a block tester to check your theory! Thanks for your advice...
I have a feeling it's the injector. Are you sure they're brand new? I bought the fiveo 1000cc injectors and they are 2nd hand high flows and one even had surface rust. I wouldn't recommend the high flows really. It can be difficult to cold start my engine now.
Yeh they were brand new. Even looked new - I knew they were shit injectors but needed something temporarily. You guys think it's a good idea to remove the first injector and then plug it in and crank car over to physically make sure petrol is getting squirted out of the injector? A bit of a big job to swap 1st and 2nd injectors as they are side feed and I'd have to remove the plenum.:)

I might buy a block tester to check your theory! Thanks for your advice...

Yeh they were brand new. Even looked new - I knew they were shit injectors but needed something temporarily. You guys think it's a good idea to remove the first injector and then plug it in and crank car over to physically make sure petrol is getting squirted out of the injector? A bit of a big job to swap 1st and 2nd injectors as they are side feed and I'd have to remove the plenum. :)

id defiantly give it a go, worst case after you pull everything out is that It works, then you know the injectors wont be the issue..

my old pulsar was misfiring on 1st cylinder, replaced leads, plugs, did a compression test, exc.. it was a little water in the dizzy cap... got nothing to do with rb`s but it was just a simple problem...

Edited by ..::R33GTS-T::..
  • Like 1

I might buy a block tester to check your theory! Thanks for your advice...Yeh they were brand new. Even looked new - I knew they were shit injectors but needed something temporarily. You guys think it's a good idea to remove the first injector and then plug it in and crank car over to physically make sure petrol is getting squirted out of the injector? A bit of a big job to swap 1st and 2nd injectors as they are side feed and I'd have to remove the plenum.:)

Won't there be a huge hole in the rail if you pull one injector out?

I might buy a block tester to check your theory! Thanks for your advice...

Yeh they were brand new. Even looked new - I knew they were shit injectors but needed something temporarily. You guys think it's a good idea to remove the first injector and then plug it in and crank car over to physically make sure petrol is getting squirted out of the injector? A bit of a big job to swap 1st and 2nd injectors as they are side feed and I'd have to remove the plenum. :)

You can change injectors without taking plenum off just need to take T/b off. I would say swap them small job for ruling something out.

Won't there be a huge hole in the rail if you pull one injector out?

Hahahaha... I obviously didn't think that through!

I might try removing the TB and swapping the injectors around. I'll keep you guys filled in - thanks for the help!

If you want to rule out the headgasket, there is a chemical test you use on the radiator to see if combustion chemicals (namely hydrocarbons) are entering the cooling system.

I've used this on a diesel patrol and it's a good way to easily test instead of removing the head if it is ok.

I got mine from Nissan (test kit). But i Borrowed the tool that screws onto the filler neck for the kit to fit into.

bit like a pressure test tool.

If you want to rule out the headgasket, there is a chemical test you use on the radiator to see if combustion chemicals (namely hydrocarbons) are entering the cooling system.

I've used this on a diesel patrol and it's a good way to easily test instead of removing the head if it is ok.

I got mine from Nissan (test kit). But i Borrowed the tool that screws onto the filler neck for the kit to fit into.

bit like a pressure test tool.

These kits are actually looking for dissolved CO2, not hydrocarbons.

  • Like 1

Update and questions...

Ecu is not my problem - tried a working ecu and it still dropped the cylinder.

Tested coolant for exhaust fumes... The test came back negative for exhaust fumes.

Tested injector driver voltages... Injectors 2-6 have a voltage (on the driver wire) of 14.3-14.7, however injector 1 (which relates to the dropping cylinder) had a voltage of 12.8-13.7.

I have no idea how voltage relates to injector timing and tried to search but found the information was way too technical for me! Does anybody know if this could be causing the cylinder to misfire???

Thanks for the help guys!

Low voltage will increase the latency and reduce the total opening, leading to slightly less fuel in total, but it shouldn't miss that badly. But low voltage static might indicate a bad joint or something that will drop the voltage further when it's under load (ie when the injector coil is earthed and operating).

Injector voltage is critical to their operation so I would be looking further into that. Perhaps the ground side is earthing slightly, which may cause the injector to leak.

I managed to get lucky in the sense that for about 1 minute the car stop misfiring and it gave me time to check that voltage... I've discovered that when the car stopped misfiring the injector voltage went back up to around 14.3-14.7.

It seems as though I've located where the problem is... Now it's a matter of trying to solve it.

I'll keep you guys updated. Cheers :)

I've found my issue - faulty injector. If I give it a few love taps, the voltage rises up to normal and it works fine.

Anyone care to explain why that would be happening (for educational purposes) and is there any home fixes or do I have to replace it?

Yeh I definitely will - don't ever wanna go through the headache again!

Thanks to anybody who contributed to the thread...

For future purposes and research, voltages on the injectors should be checked as it turns out a drop of 0.3 volts can cause a whole cylinder to drop!

:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...