Jump to content
SAU Community

Recommended Posts

my missus ran it on 91 with E10 while i was overseas for a week and when i got back and drove it i could feel the engine jittery. feels like incomplete burn / running lean and the car was very underpowered, even the gear shifts seemed lazy.
so yes it can run it but it will kill your engine in the long run as the mapping and engine fuel management is intended for ron 95 or 98
i tend to fill up usually when it gets half way and il alternate sometimes 95 sometimes 98 and it runs smooth, no noises, quick response and unexpected surprises.

I ran 95 for a while when I first bought mine, I have since switched to 98 because it is only about 2cpl more than 95. I haven't noticed any difference in economy or performance.

From memory, Japan has 96RON.

E10 can be anywhere from about 91 to 96 RON depending on how long it has been sitting around.

United sell premium 100.

That's what I would be using if I wasn't tuned on their e85.

United 100 octane is garbage. its not really 100octane since it uses 10% e10 to boost the octane rating. been using it until i got my car uprev tuned and now running shell 98, much better

how do you know you get better economy if you have run 98RON 'since day one'?

Would you drink diet coke or normal coke? Normal because you know that its nicer and better than its "alternative" Edited by Howaitonaito

I always used RON98 on my 350GT in the past. Had to pump RON95 into it a couple of times when I was out of town and couldn't find a station with RON98 and noticed that the engine tends to be abit more sluggish. Anyway, the manual states that premium fuel should be used and I think I recall reading somewhere that premium fuel is basically at least RON97 or more so I always put RON98 in and have done the same for my 370GT.

Would you drink diet coke or normal coke? Normal because you know that its nicer and better than its "alternative"

Not really a relevant comparison, higher octane fuel only has a higher resistance to detonation, if you aren't detonating on 95, then 98 will do nothing for you.

I found no difference between 95 or 98 in regard to economy or performance, and I only run 98 now as I believe Japan's fuel is 96 and I prefer to er on the safe side.

Ive had two nissans before this both australian delivered cars and both went further on 98 than they did on e10.

I got told to put 98 in it when i bought it and i have. Always BP ultimate or Shell V-power (v power in a v)

Ive had two nissans before this both australian delivered cars and both went further on 98 than they did on e10.

Of course. Ethanol has a lower energy density

I have had 3 Nissans before the V35 and none of them benefited from running a higher octane fuel than they were made for.

if the V35 is indeed made for 96RON, then my preference is not to go below that, which means 98 is the best option.

Edited by sonicii

Question for those who have the ability to map / record engine parameters.

Have you seen the ECU ever actually take out timing due to the knock sensor sensing knock?

The knock map is just a secondary Table for ignition values, I don't believe it alternates between the two, but just throws a CEL and then switches over.

I've seen a motor die (nil compression) due to a bad tune knocking (electrodes off the sparkplugs). Yet the knock sensor seemed to do SFA. Unless the tuner didn't complete the knock map, or the knock map wasn't touched and had higher than tuned map values, in which we'll never know.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...