Jump to content
SAU Community

Rb30Det Running No Turbo

mr30Turbo

By mr30Turbo,
in Engines & Forced Induction

 Share

Recommended Posts

discopotato03 Grand Master

discopotato03

Posted
Posted

If you didn't already have it I wouldn't buy it to start with . Better I think to have a Japanese made Nissan if you like the brand . VLs are old an thin on the ground now and I reckon the only reason you'd get an RB powered Dore is if you really like live axles . You get so much more out of R series Skylines for the money and the end result tends to be better . If I wasn't carting people around I'd look for an R32 with the RB25DE in it , I think it was called 25GT or similar .

R200 IRS , four piston brakes fall in , huge choice of wheels . Upgrades galore and heaps of spares around reasonably cheap .

Your call , A .

GTScotT Grand Master

GTScotT

Posted
Posted

Just to clarify; you keep saying DE and DET, which means twin cam. The D is for Double overhead cam. A twin cam RB30 is a custom made thing, not found in any STOCK cars.

I'll assume you have a VL Turbo because you haven't actually told us what you have..

If you have a VLT with the factory motor (RB30ET), you can drop in an NA or R31 RB30E and legally drive around. This is legal because the car was available with that option.

If you have something that did not come with an RB30 from stock it will be illegal to put one in and drive it on your Ps.

Its been said before but it is definitely going to be easier to sell the turbo car as it is, or put it away for now, and buy a decent P plate mobile to see you through. 100% easier, less heartache, and you won't devalue the car you own now.

89CAL Grand Master

89CAL

Posted
Posted (edited)

Just to clarify; you keep saying DE and DET, which means twin cam. The D is for Double overhead cam. A twin cam RB30 is a custom made thing, not found in any STOCK cars.

It did appear in 1 car :)

Tommy Kaira M30

Edited by 89CAL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...