Jump to content
SAU Community

Recommended Posts

I thought I would post up my existing bolt ons

Nismo s tune coil overs

Hks hard pipe kit

Arc intercooler

Greedy rad

3 inch stainless exhaust

Pfc dj and hc

Thats all I can think of for now and its allready been added to as above ^^^

little update on my clutch it was sent to jim berry race clutches in brisbane to get built , i have used him before when i built my 32 gtr and the clutch was awesome. It has arrived there at his workshop problem is the flywheel that came off my engine is a nismo light weight item jim berry has always recomended not go a light weight fly wheel ever !

He told me to source an rb 30e fly wheel if possible he said these are the best and are stronger than all the r32 gts t ,gtr , r33 gts t , r34 gtt flywheels.

so i took his advice on that and have purchased one i found on gumtree on the goldcoast and he is sending it to jim tomorrow.

Once the fly wheel is machined i will have jim send it to rob in nz so he can balance it with the engine.

I picked up this type s tomei fuel reg with fuel press gauge today .

For my fuel setup I was thinking of running a walbro 460 l p/h e85 fuel pump and 2000cc xspurt injectors and this fuel reg above with stock fuel rail.

Im still unsure if I have to change fuel lines for e85 Can someone tell me . And also how much modification is needed to fit the in tank walbro pump.

post-59423-13961101233046_thumb.jpg

Ive got a similar setup going into my s15. 25neo though

same pump and reg, bosch 2000cc injectors etc

fuel lines shouldnt need replacing but while the motors out it can be a good idea to replace the rubber hoses. cheap enough from auto stores.

if its anything like a silvia the pump should pretty much attach the way the stock one does.

Edited by n_D
Ive got a similar setup going into my s15. 25neo though

same pump and reg, bosch 2000cc injectors etc

fuel lines shouldnt need replacing but while the motors out it can be a good idea to replace the rubber hoses. cheap enough from auto stores.

if its anything like a silvia the pump should pretty much attach the way the stock one does.

Cheers .

Finaly got around to stripping down motor head is off and strapped to pallet ready to send to kelford cams in nz . Sump and all bottem end accessories that rob requires for the 30 bottem end are also packed up all bolts and nuts bagged up and labeled

I will send off monday hopefully

My next mission is to detail engine bay , replace all fuel lines and fit my new trust 16 row oil cooler kit.

post-59423-13966918012687_thumb.jpg

post-59423-13966918537912_thumb.jpg

post-59423-13966918743099_thumb.jpg

post-59423-13966918941341_thumb.jpg

post-59423-13966919147398_thumb.jpg

post-59423-13966919341598_thumb.jpg

post-59423-13966919620961_thumb.jpg

my full gt3582 r turbo setup has arrived with 6 boost manifold 44 mm turbo smart ex gate,3.5 custom dump /front pipe and screamer pipe

my head has been sent to kelford cams in nz to get all the machine work done . also have sent my sump and diff and a few other bottem end pieces to rob at rips racing in nz.

things are coming along and moving fairly quickly rob has already started on my block as of 2 weeks ago.

my next decision is what what colour to paint the engine covers and inlet manifold anyone got any ideas ?? as you can see its like a candy red now

Ok guys I previously posted this in the wrong section from now on with my build I will put my questions here

As stated before I have removed my 26 out of my 33 stripped it down and sent parts away to rips in nz ro build my 26 30now I have thrown away the heat exchanger and im fitting an rb20 filter housing .

How do people configure these hoses just join them together ?

Also im running a single turbo now im unsure where to pickup my water supply and return and what to do with the original hosing under stock inlet manifold. ?

I picked up this type s tomei fuel reg with fuel press gauge today .

For my fuel setup I was thinking of running a walbro 460 l p/h e85 fuel pump and 2000cc xspurt injectors and this fuel reg above with stock fuel rail.

Im still unsure if I have to change fuel lines for e85 Can someone tell me . And also how much modification is needed to fit the in tank walbro pump.

Regarding fuel hoses, teflon braided are a good idea but not necessary. IMO if you're spending an obviously large amount of money on your setup, what's another $200 for lines and fittings? Makes working on it a hell of a lot easier too. Regardless, there is one hose that is ABSOLUTELY necessary to change if you're going to be using E85, and that's your in-tank hose from your fuel pump to your fuel lid. Regular fuel hoses are only coated on the inside and generally work ok with E85; this hose needs to have the coating on the outside too. Gates Submersible is the stuff you want there. Don't use braided in-tank, the ethanol will eat the braid.

The Walbro 460 is easy enough to fit, half hour job. The cradle will need a bit of modification as the pump is taller than the stock one, so you will need to cut off about an inch of the hard line to fit it in. I'd also recommend running larger gauge wiring direct to the pump, don't use the stock wiring harness. These pumps draw a lot of current and will melt your plug.

  • Like 1

Regarding fuel hoses, teflon braided are a good idea but not necessary. IMO if you're spending an obviously large amount of money on your setup, what's another $200 for lines and fittings? Makes working on it a hell of a lot easier too. Regardless, there is one hose that is ABSOLUTELY necessary to change if you're going to be using E85, and that's your in-tank hose from your fuel pump to your fuel lid. Regular fuel hoses are only coated on the inside and generally work ok with E85; this hose needs to have the coating on the outside too. Gates Submersible is the stuff you want there. Don't use braided in-tank, the ethanol will eat the braid.

The Walbro 460 is easy enough to fit, half hour job. The cradle will need a bit of modification as the pump is taller than the stock one, so you will need to cut off about an inch of the hard line to fit it in. I'd also recommend running larger gauge wiring direct to the pump, don't use the stock wiring harness. These pumps draw a lot of current and will melt your plug.

Cheers mate im an auto sparky so yeah will deff do the relay and wiring . So if I replace the old fuel lines with new normal fuel line that will be ok hey . And just use gates sub in tank hey

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...