Jump to content
SAU Community

Recommended Posts

Fairly new to skylines as ive only had my r33 for about a month. I want to have a crack at drift but the stock viscous lsd is very loose and unpredictable. I've done a bit of research and from what I've read the viscous lsds aren't worth wasting money on (correct me if I'm wrong).

So what are my best value for money options considering the car will still be driven on the road from time to time. ( I have no interest in welding my diff I'd rather do it right and do it once)

- Buy an new aftermarket lsd such as kaaz, nismo, cusco (expensive. Are they worth the money?)

-buy a second hand diff with aftermarket lsd installed from an importer. ( a little less expensive and lsd is already installed but worried I will get one that's worn out and needs rebuilding which could get costly)

- from what I have read Gtrs had a mechanical 2 way that works well when shimmed/rebuilt will these fit in a gtst how much work is involved and what kind of money would this set me back.

Any advice from someone with experience would be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/441360-r33-gtst-lsd-diff-options/
Share on other sites

Lots of guys into drift run a 2 way but either will suit your purposes really. All of the above-mentioned brands would be fine as they are tried and tested. Kaaz have good support and make all the clutches etc. available for rebuild if it becomes worn out down the track, unsure about availability of the others.

As above, most drift guys will likely run a 2 way over a 1.5 way.

I bought my Kaaz 1.5 way diff centre second hand from Yahoo auctions Japan and had it shipped over through Jesse Streeter. I think the 2 way diffs were even less as there were more around than the 1.5 ways when I was looking.

Cost me a bit less than $500 delivered. Had it refurb'd and reshimmed locally, then installed into my existing diff housing. Cost me around $1000 by the time it was in my car.

Diff is super tight and haven't looked back!

Best option is R34 helical. Found on later model coupe GTT only R34 manual. Good luck !

Won't need rebuilt, better street diff than clutch-type but not as good for 100% balls-out lifted wheel action on a track.

My mechanical is noisy. It makes the inside wheel skip and chatter on turns, and gives the car a good shake when cold.

It's not a daily driver though so I don't mind it.

Throw in OS GIKEN 80W-250. Calmed down my GT Pro by 90%.
  • 2 weeks later...
My mechanical is noisy. It makes the inside wheel skip and chatter on turns, and gives the car a good shake when cold.

It's not a daily driver though so I don't mind it.

Add limslip or use Nulon SAE90 GL5 oil. Mines pretty good and you don't even notice it half the time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...