Jump to content
SAU Community

Recommended Posts

Selling my 1998 Nissan Skyline R34 GT-Turbo Coupe

This is without doubt the cleanest R34 GT-T you will find in Sydney and the most mechanically sound.

Freshly imported in November 2013 and purchased through a dealer by the name of George at Dream Car World in Haberfield.

This car has been my absolute child, saying that I have taken care of her religiously over the past couple of months. Feeling the need to maintain her, I took the liberty to add Four Brand new tyres which still have almost 100% tread.

At my own expense, with sale I will offer for FREE:
- 1 Full Tune Up
- 1 Service
- 1 Cooling Systems Flush and Test
- 1 Transmission Service

This will ensure your confidence in knowing you have purchased a quality vehicle.

Here is a guide to the additions made to the car in Japan before making the trip to Australia:
- R34 GTR Front Brake Calipers
- R34 GTR Electronic Dash
- HKS Coilovers
- SSR Wheels
- 3.5" Exhaust

Besides these additions, the car is completely stock with a great interior.

Reason for selling:
- I tied up all my money into this car and seeing that I'm currently at uni and dont have a full time job, i need to sell the car to go to Canada next January
- I am in no rush to sell the car, that being said, NO LOWBALL offers please.


*** Just under 3 years Warranty remaining ***

If you have any queries, I will reply within <24 hours.

Link to comment
https://www.sau.com.au/forums/topic/441361-r34-for-sale/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...