Jump to content
SAU Community

Recommended Posts

Hi fellow skyline enthusiasts.

I am changing my rego from Nsw to ACT registration as i purchased my car from NSW but hold an ACT license.

I failed my first attempt at the Pits at the Dickson inspection station because one of the flanges on the exhaust hit the metal ridges which protude from the surrounding of the pit. I was asked to just turn as there was no point in doing a further inspection.

I am having the flanges cut off and the whole exhaust piping tucked closer into the chassis and also raising the car to a height which will clear the 90mm limit for the pit.

My car is well maintained mechanically.

I was just wondering if i would have an issue with FMIC and (intercooler piping), POD filter (secured at 2 different points) and bleed valve.

Mods to my 34 are as follows:

FMIC

POD Filter secured at 2 points

Bleed valve

Running stock boost (9psi)

3.5" HKS silent power exhaust

new Pirellis all round on 18's

Fully serviced

Any insight or previous experiences at the Dickson motor registry would be great as i don't want to throw more cash at these guys for another inspection fee of $80 plus the waiting time for a booking being 1-3 weeks.

Thanks! :action-smiley-069:

post-127522-0-41892200-1396712579_thumb.jpg

post-127522-0-43300000-1396712592_thumb.jpg

post-127522-0-83245600-1396712600_thumb.jpg

post-127522-0-13792000-1396712610_thumb.jpg

post-127522-0-97421100-1396712624_thumb.jpg

post-127522-0-67498700-1396712649_thumb.jpg

post-127522-0-05773600-1396712660_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/441539-r34-going-over-the-pits/
Share on other sites

Yeah i'll just remove it then, better than them having another excuse to do me over. I'm just worried about this piping.. i'm sure there are no holes cut into the chassis, just underneath the battery tray. I was just hoping for some peoples personal experiences at the pits.

do you know what brand of FMIC kit is on the car?

if you are standing at the front of the car looking at the bonnet follow the pipe coming out of the left of the cooler and see how it runs into your engine bay...

If it runs through any hole that has been cut by the previous owner then you are going to have troubles.... :unsure:

I just checked out the intercooler piping, it does go through a 4by5 cm hole to the right of the battery tray (not underneath). Sorry i am a complete noob! haha, hence why i am here. Could someone direct me or tell me how, or if i can get this fixed without the installation of a new FMIC. Is getting sheet metal welded on and spraying it the factory colour acceptable, or do i have to have everything engineered regardless of improvements.

Again sorry guys i am a beginner to everything in regards to turbo cars. Thanks!

All good mate, got to start somewhere and learn...

My opinion: I suggest you buy a standard SMIC (Side mount intercooler) which will come with standard piping etc and fit that. Then remove your FMIC and all piping and take to a garage for them to fit and weld a metal patch over the hole cut. This may all still not be enough. The idea here is to try and make it all look standard and hope they dont even notice the patch job..

Once you pass then you can put your FMIC kit back on and sell the SMIC and piping. Example of a SMIC on ebay that would do the job:

http://www.ebay.com.au/itm/NISSAN-SKYLINE-INTERCOOLER-R34-12-96-04-96-97-98-99-00-01-02-03-04-/271359647064?pt=AU_Car_Parts_Accessories&hash=item3f2e4b9d58&_uhb=1

Hope that helps...

do you need any help or advice on removing the bleed valve and re-connecting your stock solenoid? (hoping they have left it mounted in your engine bay, if not you will also need to grab one off ebay....

http://www.ebay.com.au/itm/Nissan-R34-Skyline-GTT-Factory-Boost-Solenoid-/290818707557?pt=AU_Car_Parts_Accessories&hash=item43b6255065&_uhb=1

Edited by mic087

Thanks so much for the advice, i am aiming for 3 weeks or less for it to go over the pits, so time is of the essence.

I'll have a look to see if the factory boost solenoid is still there and i will also look into reinstalling the SMIC.

Thanks again!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...