Jump to content
SAU Community

Recommended Posts

Have a Au XR6 falcon ute and trying to figure out whats doing with it. Its using like 22L/100km and can actually see it puff out black smoke when free reving it.

It runs ok with an intermittent roughness like its trying to stall on me and a few times has cut out completely on me while driving, usually as I come to a stop at a traffic lights it will get rought and the revs come down to 400-500rpm. 90% of the time she'll run perfect though.

This weekend I removed the manifold and found the intake manifold flooded with what looks like fuel, so ive installed new injectors and tightened all intake manifold bolts and resealed the plenum. Took it for a drive and still doing the intermittent wanting to stall and coughing black smoke, no engine warning lights on and will idle perfect most of the time. so got me stumped.

Have read the falcon forums and I think people on here might have more knowledge.

Just looking for sensible idea's, suggestions and not smart ass comments. Apart from this issue its a good vehicle, dual fuel and just got a paint job.

post-70965-0-24759700-1398591205_thumb.jpg

Edited by AngryRB

I have a second shitbox falcon same model so I can try swapping sensors but a few mechanics said if theres no engine warning lights on then the sensors should be fine

would a blocked cat cause rich fuel mixture?

Edited by AngryRB

tomorrow Im gonna take it to exhaust shop and have the cat and front muffler replaced with a straight thru pipe, then replace the coolant temp sensor, 02 and map sensor with the other falcons that runs

perfect..

thanks for the help so far ..

Edited by AngryRB

Try an ecu reset. Disconnect the battery, hold your foot on the brake for 30 seconds, reconnect battery. If it's getting stuck on the cold map this should probably fix it. If not then hunt elsewhere.

The 4l doesn't have a maf. You've already replaced the inj so I'd check the reg. you're about 13l too rich, that's a lot for a few dud sensors.

this is correct, it has a map sensor which a vacuum leak will cause the car to run rich

It's a maP sensor not a maF sensor so it measures vacuum in the inlet manifold, the more you open the throttle (more load) the less vacuum is in the manifold.

So if you have a vacuum leak the maP sensor believes there is more load on the engine and injects more fuel

MAF= Mass Air Flow

MAP Manifold Absolute Pressure

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...