Jump to content
SAU Community

Water Pump Failure

thebawse

By thebawse,
in General Maintenance

 Share

Recommended Posts

thebawse Apprentice

thebawse

Posted
Posted

Hi guys.

On the weekend I did the cam belt, tensioners + water pump on my gts25t with brand new 'genuine' Nissan parts. All went smoothly and the car was running fine till this afternoon + a bit of 'spirited' driving caused this:

DSCF0400

The crack runs about 240degrees around the shaft and there is a chip out of it as you can see.

My question is obvious, WHY?

Was my alternator belt so tight it caused this? I didn't use a belt tensioner but I know it wasn't overly tight and the belt is in good condition as is the alternator pulley.

Or was the water pump a faulty product? Can anyone confirm if it is 'genuine' based on this number?

DSCF0401

I just want to get a heads up before I go back to the seller.

Link to comment
https://www.sau.com.au/forums/topic/442422-water-pump-failure/
Share on other sites
thebawse Apprentice

thebawse

Posted
  • Author
Posted

Water pump bolts were torqued to spec. The belt wasn't tensioned as I don't have a belt tensioner, but I was able to give the belt a 1/4 turn on the top and bottom.

It took less than 30kms for this to happen.

Would it have a chip out of it like that if the belt was over tight?

I'd classify myself as an 'advanced' DIYer. First time doing a cam belt change but not the first time dealing with auxiliary belts.

Ben C34 Grand Master

Ben C34

Posted
Posted

Thanks, that puts it in perspective. Some guys have absolutely no clue and do things up mega tight.

personally I always err on the side of loose, as you will know if it's too loose (it squeals) but too tight is harder to know.

I don't think many people use a tension gauge.

The thing is as you would know if you are super strong you can get a quarter turn on pretty much any belt no matter how tight it is. Have you been working out lately :)

89CAL Grand Master

89CAL

Posted
Posted

hmmm that makes it interesting then

why did you put quotation marks around genuine? Was it not from a completely reliable place or second hand or something along those lines?

That might be my only concern now. If bolts were done up right, and sounds like the tension was O.K (without knowing how hard you were turning it to get 1/4 of a turn)

I have my own 1/4 of a turn method that I've been doing for quite a while now on alot of different belts (heavy machinery mostly) and usually is pretty good on your standard v-belts. But as said, I've been doing it my way for years with no issues, but your way and my way might be the same in theory but completely different lol.

thebawse Apprentice

thebawse

Posted
  • Author
Posted

Haha, that's a definite no on the working out! My arms got tired after just doing this job.

The parts were from a Nissan dealer, more specifically from here:

http://www.trademe.co.nz/Browse/Listing.aspx?id=715037326

I put quotes around genuine as the cam belt came in a package labelled 'A31 RB20DE' and the water pump is marked '3Y07' which is different from the old one. I know neither of these things are necessarily bad and they might both be genuine and correct parts for an RB25 so hopefully one of you guys can confirm this for me so I can put that one to rest?

jiffo Mentor

jiffo

Posted
Posted

When you stripped it down to inspect the damage, was the alternator belt still sitting properly in the various pulley grooves?

Hadn't tried to climb off or anything?

I have seen pumps go like this previously, but they were no-names.

If you break the pump right through at that crack I think you'll be amazed how thin the metal is.

thebawse Apprentice

thebawse

Posted
  • Author
Posted

When you stripped it down to inspect the damage, was the alternator belt still sitting properly in the various pulley grooves?

Hadn't tried to climb off or anything?

I have seen pumps go like this previously, but they were no-names.

If you break the pump right through at that crack I think you'll be amazed how thin the metal is.

Yeah mate all belts were in line and are undamaged, no nicks out of them or any cracks.

Comparing the old pump with the new, the new one does seem to be a bit lighter and not of the same quality. That could be my imagination telling me what I want to hear though.

thebawse Apprentice

thebawse

Posted
  • Author
Posted
Saw this failure on my mates Mazda after we put a new wp on, we went with manufacturing defect but would be interested in other thoughts. (Mechanic by trade so I'm confident in the workmanship :))

I'm sending it back to the Nissan dealer for them to have a look. I'll let you know what they say.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Slight brake pedal stutter after new pads

      By MBS206 · Posted

      Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • PranK
      Slight brake pedal stutter after new pads

      By PranK · Posted

      Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • GTSBoy
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By GTSBoy · Posted

      My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...