Jump to content
SAU Community

Recommended Posts

Yeah will find out. I think you should vent the BOV to atmo. There is atleast 1k RPM in response. and an extra 200kw

already is.

lololololztutututututututututututu.

I have a couple of Pure JDM HKS ones that vent to atmos that were loud as fk on my gtr.

Like these:

SDC13973.jpg

But srsly Plumb it back properly bruh

lol, there is nothing there to plumb it back too mate. at all. maybe if someone coughed up a gtr bov, i could get scotty to weld someting up.

I'm sure someone in vic will have a stock BOV floating around?

Those HKS ones are loud as f**k. Twas great.

I don't has Stock ones spare as i went back to stock to make motor run betterererer

It's possibly the cooler is too big. What about running like a 200sx cooler or stock r33 gts-t cooler? something smaller? That's a question for someone that really knows what they are talking about

Dump should make quite a bit of difference.

EVO 6-9 intercooler would be best :yes:

EVO 6-9 intercooler would be best :yes:

going by the size of them mick i dont think it would make that much difference!!!!!!!! but its something i can look into at a later date.

right i started pulling it down last night. turbo, cooler, dump and manifold off.

gotta check all the timing marks are in the right place and take the chain off. then cams out and head off. excited too see what state a 300km engine is in......

dump pipe is so obviously a restriction its mad. its f**king tiny and must be destroyed. cue scotty and a custom one.

or does anyone have one r33 gtr dump pipe aftermarket available?!

just a quick recap of parts,

custom front pipe 2.5 inch to cat, 2 inch to VAG diesel muffler built by scotty. thanks!

stock gtr 33 dump and turbo. thanks grant for supplying!

custom cheapo ebay knock off hks filter that bolts straight to the turbo. thanks ebay!

custom very short cooler piping. cheers scotty.

ford xr6t intercooler again scotty with some help from alvin

stagea/r34 370cc injectors. you guessed it, scotty!

r33 gtr fuel pump thanks greg!

custom made knive edge steampipe manifold thanks scotty

soon to be jdm plastic rocker cover, micra

arp studs, usa. actually from a ford escort....

ga15 throttle body and afm, my mate in NZ

sr20 oil filter re locator modified to fit cg13, with un regulated oil cooler.

nistune'd by dmd tuning on e85. thanks david

jun 4.2kg flywheel (10kg lighter) micra forum.

exedy heavy duty clutch. same

bc coilovers front, kyb shocks rear with tein springs not telling.

nismo rear sway bar, whiteline pan hard rod. micra forum for sway and me dad for xmas for the rod!

rear disc brake axle conversion. harveys wreckers in langwarrin. great blokes.

front n14sss brakes with hel braided lines, rda slotted and dimpled rotors and qfm a1rm pads. brakes from wreck, lines rotors and pads supplied by jason at garage 9. thanks!

super s front bumper. harveys langwarrin.

n14sss/gtir wheels wreck.

suziki swift ver3 recaro front seats, tony tran, thanks man.

n13 pulsar steering wheel. wreck.

i think thats about it!

thanks to dave as well for coming and being my eyes the night before roady when i couldnt f**king function any more.

if ive missed anyone, please chirp up its been that long and ive had that many parts from you all i cant remember!

one last thing, scotty is a mate, but 90% of the things he supplied and built where paid for. he is a buisness after all! the other ten percent was bourbon, jerky and foaming hand shandies.

Good list of parts mate. Whats the filter element like in your Pod filter? That could also be restricting you a little bit?

Get us the dyno chart reading when it next goes up!?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...