Jump to content
SAU Community

Recommended Posts

Hi Everyone,

I've decided that a GT3076r or ATR43SS2 will be what will make my setup complete....i'll be happy with anywhere between 250kw-300kw.

my question is this, i have no idea what would be the ideal sized external wastegate... i want to limit exhaust or manifold modififications so was looking for a 0.82 rear housing with the flange for the wastegate and utilizing a vband clamp of the rear.

any suggestions or advice on the size?

cheers

Gaz

Link to comment
https://www.sau.com.au/forums/topic/442821-external-wastegate-size-for-gt3076r/
Share on other sites

Turbosmarts come with either 7 or 14psi springs standard, then you buy other springs to get your desired boost pressure.

Also it might sound simple but i have no idea how technically minded you are. Make sure you buy springs that equal slightly less than your desired pressure, as you cannot run less boost that the wastegate spring pressure.

Turbosmarts come with either 7 or 14psi springs standard, then you buy other springs to get your desired boost pressure.

Also it might sound simple but i have no idea how technically minded you are. Make sure you buy springs that equal slightly less than your desired pressure, as you cannot run less boost that the wastegate spring pressure.

yeah i did know this...i still like to be able to turn my boost down when i have to leave it anywhere.

I ran an internal gate on my gtx3076r holding 18 psi flat line but 22psi needed a external gate to control it. Now I have a tial 44mm of the housing

i'm running 18psi at the moment....i'm not sure i'd push more boost on my old block (300,000km)

I use a 45mm Turbosmart Hypergate off a Hypergear SS2, happily runs 0.5 bar all the way to 1.2 bar and holds to red line.

Will be dialling in 1.5 bar once I get my injectors sorted out, right now stock injectors are hitting 92%... great spray pattern haha

The Hypergear is an internal gate housing, probably best if you buy a suitable external gate housing and get Stao to machine that to suit his turbine wheel if you are heading down that path.

With the GT3076 you can buy Vband housings for them cheap off Kinugawa, ship it to me and I can weld the gate to it. (unless you can find a decent fabricator locally, but you will need to take the car there.)

The Turbosmart gates are great and will hold over 45psi these days since the HP caps were released, but i assume you are sticking to 98... I would be running e85 for engine protection if you are worried about longevity

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A lot of the trim pieces on the E39 are super brittle and just dissolve when you try to get them off. It looks like a previous owner has used what can only be described as an industrial construction foam adhesive to glue down a tiny piece of trim.  Unfortunately this part of the tailgate is starting to rust because of how much shit is in here. This is stopping the water draining and there's a big build-up of dirt that is just staying wet. How can I remove this? Would a flap disc get rid of this?  I think this car spent a lot of time inland. There's so much light coloured, fine dirt and dust everywhere.  Sorry for the pic. I've cleaned this all up now so I'll get another pic of it clean today.
    • Surely, just about any shop that has done a Skyline (or Supra, or RX-7, or EVO, or WRX) will have done E85. But perhaps you need to specify what type of car, what type of engine, what ECU, you propose to be using.
    • Try an oil additive. There's a couple of options for "easier shifting". These are essentially a similar idea to what Redline put into their Shockproof gear oils. I had a 2nd hand R33 (in fact, as of right now, it is still in the car) that simply would not engage any gear with the engine running, with normal gear oil in it. We dropped that and replaced it with Shockproof lightweight, and suddenly the gear lever did what it was supposed to. At a cost, of course, of the then ongoing damage to internals done by running Shockproof. But the synchros were already totally uninterested in life, so there was no loss.
    • It always ends with the car burning down.
    • I see what you posted, but how could a warning light be going on and off if there is no sender for it?  The only other explanation is that the wire that used to go to the sender from the warning light is earthing somehow in the loom or at the connector, or that you have connected the warning light wire to something (maybe the temp sender?).  
×
×
  • Create New...