Jump to content
SAU Community

Recommended Posts

10325392_678842408830830_295853600890345
EVENT: SAU NSW Texikhana

LOCATION: Nirimba Airfield / TAFE / Skidpan - same place as last time (yeah, it's got a few names)

Location map: https://goo.gl/maps/JZdPt

Date:9th June 2014 (Yes it is on a Monday - Queens Birthday long weekend)

What is it:Motorkhana courses marked with orange things that we'd kindly appreciate if you drove around rather than over

Entry Cost SAUNSW members:$55 Entry fee

Entry Cost NON SAUNSW members:$75 Entry fee (If you plan to enter more than 1 or more events with us it pays to be a funded member)



Entries strictly capped at Max. 30 cars. This guarantees loads of runs and minimal wait time but if you don't sign up, well you snooze you lose. So get in quick to reserve your spot.



Spectators:Free to watch

Lunch:BBQ will be $3 snag sandwich and $1.50 cans (selection of flavours available)

Passengers:$10 which is cheap compared to other clubs and events, (SUPPORTS OUR CLUB!!!) , MUST sign on, MUST wear wrist to neck/ankle clothing with enclosed shoes and approved helmet, same as drivers. All passengers must sign a passenger indemnity form on the day. Under 18 years must have parent or guardian permission.

Courses: Released on the day at sign on

First Timers:Don't be shy, you'll love it.



Those of you that have been to one of these before will agree, this is the best money you can spend as far as driving time for an event. The event will be run after run until 4.30pm, and considering most runs are under 1 minute AND that we're kicking off at 9am, that's a lot of runs :thumbsup:



This is a safe event where you only go as hard as you want to, there's no pressure, one car on a course at a time. Perfect for beginners to have a first try at driving their pride and joy off the streets.



With that said, there's usually some friendly competition between mates, which is great to watch :D

Timing for the day:



Scrutineering/sign on starts - 7.00am

Scrutineering/sign on ends - 8.30am (don't show up at 8.25am, come with plenty of time to spare)

Drivers brief - 8.40am (mandatory attendance all drivers)

Runs start - 9.00am

Lunch approx - 12.30pm depending on how the day is going (One hour)

Runs stop - 4.45pm

Gates close - 5.00pm


Entrants please note:


-Passengers must not be under the age of 15 years. All under 18 year old passengers must sign a passenger indemnity on the day and must have approval from their parent or guardian. If the parent or guardian is not present at the event, a letter giving permission to participate must be received

-All entered cars must arrive in time for and pass scrutineering, no exceptions.

-All drivers must be licensed (AASA or CAMS) and show valid licence and expiry date at sign on.

-All cars must have an insurance approved fire extinguisher secured within drivers reach.

-Sidepipes are not allowed. Screamers/external gates venting to

atmosphere are also not allowed to be entered. No exceptions (this is

not my choice, I ♥ gate)

-Entries are open now, entries close as stated in Supplementary

Regulations (at bottom of this post) to allow time for officials to

organise paperwork.

-Supp regs and Entry Form are soon to be attached. Entry forms without payment will be rejected.

-Yes you can join SAUNSW on the day (allow an extra 5mins at sign on)

-There is no EFTPOS/Credit Card machine on site, so bring cash and we

will have change there for you. If you can bring close to the right

amount, that's helpful.



Regarding your motorsport licence:



Due to changing policy at AASA we cannot process licence applications on the day. AASA or CAMS licences (or proof thereof) must be organised prior and brought to the event. AASA can provide a fax confirmation of your licence status if you require one at shorter notice (bare minimum 2 weeks). Also, CAMS licences can be renewed online if you have previously held an L2NS or L2S. URL HERE:
http://australianautosportalliance.com/wp-content/uploads/2011/09/CLUB-LICENCE-APPLICATION1.pdf









HOW TO ENTER:




Electronic entry details sent to [email protected]


Please include:

Full Legal Name (as entered on bank deposit):

Forum Alias:

Car Make:

Car Model:




The only way to secure a spot is through sending in an entry form/email and payment through Eventbrite,

https://www.eventbrite.com.au/e/saunsw-9th-june-texikhana-tickets-11579640015


or by the bank details are below:



SAUNSW bank details:

Bank - NAB
Branch - Marrickville
Account name - Skylines Australia NSW
BSB - 082 356
Account number - 546 393 766

Please put your FULL NAME in the description, eg "TEXI JOE SMITH"

So Enter NOW!

AASA Passenger Indemnity - with under 18 years.pdf

Supp Regs and Entry Forms.pdf

Edited by crashdown

Mines on its way out and the new one will be ordered soon and due to go in sometime in june anyway.

I'm determined to destroy it lol

just make sure you have a way of getting it home if it does go...
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...